680782
65
Zoom out
Zoom in
Previous page
1/88
Next page
65
S10931-00001_Rev-D_EN
13. Function test and final test
13.1 Testing obstacle detection
Observe in particular the following safety instructions for
this chapter.
After initial operation of the operator, the force
measurement of the operator must be checked with
a force measurement device and an obstacle detection
test must be performed.
WARNING
Danger due to projecting parts!
Door leaves or other parts must not
project into roads or public footpaths.
This also applies while the door is
moving.
This may cause serious injury or death
to persons or animals.
Keep public roads and footpaths clear
of projecting parts.
WARNING
Danger of entrapment!
If the force setting is too high, persons
or animals in the movement area of the
door may be trapped and pulled along
with the door. Severe injuries or death
may result.
The force setting is relevant to safety
and must be carried out by a qualied
specialist.
You must proceed with extreme caution
if you check and if necessary adjust
the force setting.
WARNING
Danger of crushing and shearing!
If the door moves and there are persons
or animals in the movement area,
crushing and shearing injuries may be
caused by the mechanism and safety
edges of the door.
Note that obstacle detection does not
operate below 50 mm.
The obstacle detection must be tested
once a month.
Only use the operator when you have
a direct view of the door.
All danger zones must be visible during
the entire door operation.
Always keep the moving door in sight.
Keep persons and animals clear of the
range of movement of the door.
Never put your hand near the door
when it is moving or near moving parts.
In particular, do not reach into the
moving push arm.
Do not reach into the ceiling suspension
unit when the motor carriage is running
along the track.
Do not drive through the door until it has
opened completely.
Never stand under the opened door.
NOTE
Observe the national standards, guidelines
and regulations for cut-off of the operating
forces.
NOTE
The obstacle detection must be tested
once a month to prevent damage to the
operator.
INFORMATION
After installation of the operator, the
person responsible for the installation
of the operator must complete an
EC Declaration of Conformity for
the door system in accordance with
Machinery Directive 2006/42/EC and
apply the CE mark and a type plate.
This documentation and the installation
and operating manual for the operator
must be handed over to the user.
This also applies if the operator is
retrotted to a manually operated door.
65


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sommer S 9080 pro at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sommer S 9080 pro in the language / languages: English as an attachment in your email.

The manual is 10,04 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sommer S 9080 pro

Sommer S 9080 pro User Manual - German - 88 pages

Sommer S 9080 pro User Manual - Dutch - 88 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info