680782
61
Zoom out
Zoom in
Previous page
1/88
Next page
61
S10931-00001_Rev-D_EN
11. Connections and special functions of the wall
control unit
11.10 Output OC
The door status display can be shown with the Output
OC (open collector output) accessory part. To do this,
set DIP switch 2 on the wall control unit to "ON."
P
AD
1
4
Fig. Relay slot for Output OC
The Output OC accessory part is plugged into the Relay
slot, see separate "Output OC" instructions.
11.11 Relay
External lighting such as the garage light, courtyard light
or door status display can be controlled with the relay
accessory part. The function depends on the setting of
the DIP switches. See also chapter "11.3 Setting the
DIP switches on the wall control unit."
P
AD
1
4
Fig. Relay slot
The Relay is plugged into the Relay slot on the wall
control unit, see separate "Relay" instructions. The
maximal switching capacity is 5 V, 250 V AC or 5 A,
24 V DC.
11.12 Installing and removing the
accumulator
The accumulator can bridge approximately 5 cycles
within 12 hours in the event of a power failure. Only
a qualified electrician is permitted to install, test and
replace the accumulator. See Chapter "7.1 Cover of the
motor carriage." Follow the instructions in the separate
installation and operating manual for the accumulator.
NOTE
If an accumulator has been installed,
it is connected to the circuit board.
Carefully remove the control unit cover
and disconnect the connections to prevent
damage to the wall control unit.
INFORMATION
Only an original accumulator from
SOMMER may be used.
INFORMATION
Initial operation is not supported if the
accumulator is the sole power supply.
Mains voltage is required for initial
operation of the operator.
INFORMATION
The accumulator can only be recharged for
a limited number of cycles. This depends
on the use and settings.
Installing the accumulator
Fig. 1
1. Disconnect the operator from the mains voltage.
Check that the operator is disconnected from the
power supply.
2. Unscrew the light cover from the wall control unit and
remove it upwards. Hold the front control unit cover
firmly while doing so, see chapter "7.3 Light and
control unit cover of the wall control unit."
3. Remove the control unit cover gently towards
the front and unplug the connection cable for the
membrane keypad from the wall control unit.
Fig. 4
4. Place the accumulator in the control unit cover and
fasten with two cable binders.
61


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sommer S 9080 pro at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sommer S 9080 pro in the language / languages: English as an attachment in your email.

The manual is 10,04 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sommer S 9080 pro

Sommer S 9080 pro User Manual - German - 88 pages

Sommer S 9080 pro User Manual - Dutch - 88 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info