680825
64
Zoom out
Zoom in
Previous page
1/96
Next page
64
S10564-00001_Rev-A_EN
11. Connections and special functions of the wall
control unit
INFORMATION
If a photo eye is used as a frame photo eye
on the door, move the door to the centre
position.
2-wire photo eye for door CLOSE (PHOTO 1)
TX
24 V
24 V
Sign
al
GND
GND
COM
RX
PHOTO 1
TX
2
4
V
2
4
V
GND
G
N
D
RX
P
HOTO 1
Fig. Terminal for 2-wire photo eye
Connect the 1- or 2-wire photo eye to the PHOTO 1
terminal block. The polarity is optional. The status LED
(PHOTO 1) for door CLOSE lights up orange when the
safety device has been detected by the control unit.
Terminal block Function
Signal 2-wire photo eye,
any polarity
COM
The 2-wire photo eye (PHOTO 1) is interrupted in the
door CLOSE direction:
Status LED ashes orange during the interruption.
The operator stops gently and opens the door
completely.
The door closes automatically after the open
holding and clearing time.
4-wire photo eye for door CLOSE (PHOTO 1)
TX
24 V
24 V
Signa
l
GND
GND
COM
RX
T
Y
PHOTO 1
IN
Fig. Terminal for 4-wire photo eye
Connect the 4-wire photo eye to the terminal block for
door CLOSE (PHOTO 1). The supply for RX (Receiver)
should be on the side facing away from the sun.
The status LED (PHOTO 1) for door CLOSE lights up
orange when the safety device has been detected by the
control unit.
Terminal
block
Function
TX (Trans-
ceiver)
+24 V DC
Power supply
GND
RX
(receiver)
+24 V DC
GND
SIGNAL Potential-free relay
contact
COM
The photo eye (PHOTO 1) is interrupted in the door
CLOSE direction:
Status LED ashes orange during the interruption.
The operator stops gently and opens the door
completely.
The door closes automatically after the open
holding and clearing time.
Use as frame photo eye
1. Install the frame photo eye in the frame, see separate
"Frame photo eye" installation instructions.
2. Align the frame photo eye and connect to the wall
control unit.
3. Commissioning is performed as described in Chapter
"9. Commissioning".
If the door passes the frame photo eye, the
illumination power of the operator lighting is
reduced.
If the illumination power is not reduced, the frame
photo eye must be realigned and the control unit
must be reset.
During commissioning, the operator learns the
exact position of the frame photo eye in order to
blank it out in normal mode shortly before reaching
the door.
4. Check the frame photo eye function.Repeat the
process if necessary.
64


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sommer S 9060 Tiga at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sommer S 9060 Tiga in the language / languages: English as an attachment in your email.

The manual is 28,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sommer S 9060 Tiga

Sommer S 9060 Tiga User Manual - German - 96 pages

Sommer S 9060 Tiga User Manual - Dutch - 96 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info