680825
51
Zoom out
Zoom in
Previous page
1/96
Next page
51
S10564-00001_Rev-A_EN
10. Connections and special functions of the carriage
10.11 Deleting all radio channels in the
receiver
1. Press and hold the radio button for 30 seconds.
The LED ashes after 15 seconds.
After another 5 seconds the ash sequence
changes to ashing.
After another 5 seconds, the LED of the selected
radio channel remains steady.
After another 5 seconds all LEDs light.
2. Release the radio button.
All LEDs are off after 5 seconds.
All programmed transmitters are deleted from the
receiver.
Receiver is completely deleted, this also applies if
the Memo is plugged in.
10.12 Programming a second transmitter
by radio (HFL)
Prerequisites for teach-in by radio
A handheld transmitter must already be programmed
on the radio receiver. The handheld transmitters used
must be identical. So, for example, a Pearl can only be
programmed on a Pearl and a Pearl Vibe on a Pearl Vibe.
The key assignment of transmitter (A) that put the radio
receiver into teach-in mode by radio is used for the new
transmitter (B) that is to be programmed. The already-
programmed handheld transmitter and the new handheld
transmitter to be programmed must be situated in the
range of the radio receiver.
Example:
1. Button 1 on radio channel 1 and button 2 on radio
channel 2 have been programmed by handheld
transmitter (A).
The newly-programmed transmitter (B) adopts
the key assignment of transmitter (A): Button 1 on
radio channel 1 and button 2 on channel 2.
Restrictions
The targeted teach-in of a selected transmitter button on
a radio channel is not possible.
1
2
A
3
B
Fig. 1
1. Press buttons 1 + 2 of a programmed transmitter (A)
for 3 - 5 seconds until the LED lights up on the
transmitter.
The operator lighting ashes.
2. Release buttons 1 + 2 of the transmitter (A).
If a radio command is not transmitted within
another 30 seconds, the radio receiver switches
over to normal mode.
3. Press any key, e.g. (3) on the new handheld
transmitter (B) to be programmed.
The LEDs of the operator lighting remain steady.
Handheld transmitter (B) has been programmed.
10.13 Resetting the control unit
15 s1 s 5 s 10 s
Reset of the
safety inputs
Force values
deleted
Position
values and
frame photo
eye deleted
Factory
settings
restored
Fig. Overview of the time sequence of the carriage status LED
when pressing the green reset button
RADIO
RESET
CH1
CH2
CH3
CH4
STATUS
ON
1
2
3
4
Fig. 1
51


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sommer S 9060 Tiga at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sommer S 9060 Tiga in the language / languages: English as an attachment in your email.

The manual is 28,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sommer S 9060 Tiga

Sommer S 9060 Tiga User Manual - German - 96 pages

Sommer S 9060 Tiga User Manual - Dutch - 96 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info