680825
49
Zoom out
Zoom in
Previous page
1/96
Next page
49
S10564-00001_Rev-A_EN
10. Connections and special functions of the carriage
10.3 Reducing illumination power of
LEDs
WARNING
Danger due to optical radiation!
Looking into an LED at short range for
an extended period may cause optical
glare.
This may temporarily reduce vision.
This may cause serious or fatal
accidents.
Do not look directly into a LED.
The illumination power of the LEDs of the operator
lighting can be reduced during adjustment work on the
carriage.
1. Press the radio or reset button briefly one time.
Illumination power of LEDs reduced.
10.4 Explanation of radio channels
LED radio channel Setting/function
1 CH 1 Multi-function relay/lighting
2 CH 2 Partial opening
3 CH 3 Exterior request side
4 CH 4 Interior request side
INFORMATION
If you want the lighting function via the two
multi-function relay, this function must be
congured via SOMlink, a WLAN-enabled
device and the Memo tiga.
10.5 Programming the transmitter
RADIO
RESET
CH1
CH2
CH3
CH4
STATUS
ON
1
2
3
4
Fig. 1
INFORMATION
If no transmission command is received
within 10 seconds of pressing the radio
button, the radio receiver switches to
normal operation.
1. Press the radio button repeatedly to select the
required channel.
LED 1 x 2 x 3 x 4 x
CH 1
CH 2
CH 3
CH 4
2. Press the desired button on the transmitter until the
previously selected LED (CH 1, CH 2, CH 3, CH 4)
is off.
LED goes out - programming is complete.
The transmitter has transferred the radio command
to the radio receiver.
3. Repeat the above steps to program additional
transmitters.
INFORMATION
Further transmitters cannot be
programmed if all memory slots of the
handheld transmitter are occupied.
If the memory capacity has been reached
All 40 transmitter commands are available for all
channels. If an attempt is made to program additional
transmitters, the red LEDs of radio channels CH 1-CH 4
flash. If more memory space is needed, see Chapter
"10.6 Information on Memo".
10.6 Information on Memo
The memory capacity can be extended to 450 transmitter
commands using the optional Memo accessory part.
When plugging in the Memo, all available transmitters are
transmitted from the internal memory to the Memo and
stored there. The Memo must remain plugged in on the
control unit.
No more transmitters are stored in the internal memory.
Stored transmitters cannot be transmitted from the Memo
back to the internal memory.
49


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sommer S 9060 Tiga at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sommer S 9060 Tiga in the language / languages: English as an attachment in your email.

The manual is 28,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sommer S 9060 Tiga

Sommer S 9060 Tiga User Manual - German - 96 pages

Sommer S 9060 Tiga User Manual - Dutch - 96 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info