634115

Solo 106 Manual

25
Zoom out
Zoom in
Previous page
1/100
Next page
25
FIG. 10
5. Insert the line trimmer (1) and secure with
two screws (2).
5.4
Contact protection installation (model 105)
FIG. 11
1. Turn the shaft end (1) so that the cut-out is
flush with the hole in the shaft interior (2).
Insert the handle of the included spark plug
spanner (3) as locking pin and, thereby, lock
the rotary shaft. Thread and tighten the Line
head clockwise onto the rotary shaft. Remove
the spark plug spanner and keep in a safe
place.
2. When removing the Line head, turn the
shaft end again so that the cut-out is flush
with the hole in the shaft interior. Insert the
handle of the included spark plug spanner as
locking pin and thereby lock the rotary shaft.
Remove the Line head by turning it manually
anti-clockwise from the rotary shaft.
1. For model 106B, the contact protection (if
in the form of metal wings) is secured to the
shaft tube with two clamps (1). The overlong
gearbox fixing screws (2) must protrude into
the holes in the contact protection shield
(anti-rotation protection).
2. When fitting the line head (model 106L and
106R), insert the spacer (3) included in the
delivery with two M5 x 55 screws between the
lower clamp and the contact protection shield.
The overlong gearbox fixing screws (4) must
protrude into the holes provided in the spacer.
Fit the line trimmer blade (5) into the holes
provided in the contact protection shield.
1
2
3
FIG. 12
2
5
4
3
1
5.6 Cutter installation (model 106B)
FIG. 13
Never operate without fitted contact protec-
tion.
5.5
Touch protection installation (model 106)
1. Position the clamp (2) in the correct way
(with the angled edge pointing towards the
gearbox) on the gearbox output shaft (1).
2. Note: The internal recess in the clamp
should point away from the gearbox to enable
this recess to accept the corresponding raised
part in the boss washer (5).
3. Turn the gearbox input shaft with the clamp
so that the recess for the locking pin (3) is
flush with the recess in the winding protection
(4) or the gearbox housing.
1
2
… 25 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Solo 106 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Solo 106 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 0,53 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info