Manual Solo 106 (page 23 of 100) (English, German, Dutch, French, Italian, Spanish)

634115

Zoom out

Zoom in

1/100

5. Assembly

1. The equipment will be despatched part-

assembled, and should, therefore, be fully

assembled before taking it into use. Only use

this machine when it is completely assembled.

Ensure that the tank is fully drained before

any assembly, disassembly or modification.

4.8 Maintenance and repair

1.The power tool should be regularly main-

tained. Only execute the maintenance and

repair work yourself that is described in these

operating instructions. All other work should

only be executed by a specialized workshop.

2.For cleaning, maintenance and repair the

motor should always be shut off and the

sparkplug connector should be removed. An

injury hazard through the motor starting

unintentionally. Exception is adjusting the

carburettor and idle.

3.Only original replacement parts from the

manufacturer may be used.

4.No changes may be made to the power tool,

as this could impair the safety of the device

and cause a hazard of accident or injury!

5.The power tool may not be maintained, re-

paired, or stored in the vicinity of open flame.

6.Regularly check the fuel tank cap for leaks.

7.Only use sparkplugs that are problem-free and

that are recommended by the manufacturer.

8.Check the ignition cable for problem-free

condition and intact insulation. If the

sparkplug is unscrewed or the ignition cable is

removed from the socket, then only move the

device if the stop switch is placed on “ 0 /

stop”). A fire hazard exists through sparking!

9.Regularly check the noise suppressor for

problem-free condition. Do not touch the

noise suppressor, as long as is still hot.

5.1 Loop handle (models 105, 106L and 106R)

FIG. 5

1. Turn the loop handle into the correct position.

2. Note: Always install the safety end-stop (1)

on the operator side of the motorised scythe.

If, during use, you carry the motor scythe on

your r.h. side, install the safety end-stop in l.h.

orientation. However, if, during use, you carry

the motor scythe on your l.h. side, install the

safety end-stop in r.h. orientation.

3. Install the safety end-stop (1) on the loop

handle and secure with the spring clip (2).

Never blow in the direction of other people, as

smaller objects can be forced upward at high speeds.

10.Implement the power tool at lowest possi-

ble noise and exhaust levels. Only open the

throttle when working, do not let the motor

run unnecessarily. Please note that noise also

impacts the environment. Observe the quiet

times, that can vary from place to place.

11.Exercise caution when the ground is wet,

with ice and snow, on overhangs, or uneven

terrain. There is an increased risk of slipping!

11.b. Pay particular attention to safety when

working on slopes. Before commencing work,

check the working area for stones, broken

glass, nails, wire or other solid objects and

remove such debris to prevent them being

picked up and thrown out by the cutters.

11.c. Always hold the cutters below hip level. Never lift a

rotating cutter off the ground. Keep all parts of the

body away from rotating cutters.

11.d. Only use cutters in perfect working order

(see chapter 8 ”Using the motor scythe”).

11.e. Never use blunt cutters and avoid uncon-

trolled contact of the cutter with debris. Oth-

erwise there will be an increased risk of kick-

back, which could throw the entire machine

around. Consequently, the operator could be

subjected to involuntary movements, which

could lead to serious injury or death.

11.f. Always stop the engine before any con-

tact with the cutter – even when clearing a

blockage or if cutters have become jammed –

wait until the cutter has stopped and remove

the spark plug cap.

11.g. Stop the engine if you notice a differ-

ence in the operating characteristics of the

motor scythe.

11.h. Due to the centrifugal clutch, the cutters

will run on for a short time, even if you release

the throttle. Ensure the cutter has fully

stopped before storing the machine.

12.Pay attention to obstacles or stumbling

hazards such as tree roots, tree stumps, edges.

13.Do not touch the exhaust and the noise

suppressor, as long as they are still hot, there is

a danger of burn injury!

14.Never work with defective noise suppressor

or without noise suppressor. There is a hazard

of hearing damage and burn injury hazard!

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Solo 106 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 0,53 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Solo 106 Manual

Product: