Manual Solo 106 (page 24 of 100) (English, German, Dutch, French, Italian, Spanish)

634115

Zoom out

Zoom in

1/100

4. Model 105:

5. To secure the loop handle, tighten screw (3)

with a screwdriver. We recommend the T-25

Torx key integrated into the enclosed spark

plug key. During tightening, hold the opposite

nut with an open-ended spanner.

6. Model 106L and 106R:

7. To secure the loop handle, tighten screw (3)

by hand and tighten the quick-acting lock by

flipping it over.

FIG. 7

1. Loosely secure both half clams of the upper

handle support (1) with two enclosed screws on

the two-handed bike handle. Fit the r.h. side of

the two-handed bike handle as near to the

handle support as possible. Then position the

upper handle support with the two-handed

handle onto the lower handle support.

Insert the square nut for the central screw (2)

into the lower handle support, and loosely

thread the central screw (plus washer)

through the handle support into the square

nut.

FIG. 8

2. The optimum adjustment is ensured, when

the centre of the machine is level with the

centre of the operator’s body. Elbows should

be slightly angled in the working position. In

this position, lock the upper handle support

into the teeth of the lower handle support,

and tighten the central screw (Fig. 7.2) incl.

washer. Then also tighten the two screws in

the upper handle support in this optimum

position.

3. Always lead the motor scythe with the two-

handed bike handle on the r.h. side of the body.

4. Please note: Never stress the cable between

the handle and the engine (throttle cable and

engine stop cable), otherwise the engine will

not be able to idle, and the cutters will always

be running. Therefore, check before every

engine start that the carburettor lever is per-

fectly slack when the throttle is set to idle and

is only moved when accelerating.

5.3

Touch protection installation (model 105)

1. Never operate without fitted con-

tact protection.

2. Position the motor scythe inverted on the

ground, so that the shaft (1) points upwards.

3. Please note:

Prevent the tank from spilling fuel.

4. Insert both square nuts (2) from below into

the contact protection (3). Locate the contact

protection on the shaft, so that it points to-

wards the operator. Locate the groove in the

contact protection precisely on the shaft tab.

Evenly tighten the contact protection with the

clamp (4) and both fixing screws (5).

FIG. 9

5.2 Two-handed bike handle (model 106B)

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Solo 106 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 0,53 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Solo 106 Manual

Product: