603162

Skytech 3002 Manual

4
Zoom out
Zoom in
Previous page
1/10
Next page
INSTALLATION INSTRUCTIONS
The remote receiver can be Wall Mounted into a standard plastic switch box or (Hearth Mounted) placed on or near the
replace hearth. Determine where you will install the receiver before proceeding. Preferably, the remote receiver should
be wall-mounted in a plastic switch box, as this will protect its electronic components from both the heat produced by the
gas appliance and potential damage or abuse that can occur if it is left exposed on the hearth. PROTECTION FROM
EXTREME HEAT IS VERY IMPORTANT. Like any piece of electronic equipment the receiver should be kept away from
temperatures exceeding 130°F inside the receiver case. Battery life is also signicantly shortened if batteries are exposed
to high temperatures.
When installing the receiver into a switch box ensure the receiver switch is in the OFF position before installation. The
receiver is supplied with 18-inches of wire. If additional wire is required it is recommended that 18 gauge stranded or solid
wires (not included) be used to make connections between the terminal wiring block on the millivolt gas valve or electronic
module and the wire terminals on the remote receiver. For the best results, use 18 gauge stranded or solid wire, splice
into the black wires of the receiver or remove the black wires and install wires directly to the receiver. Be sure no splices
measure longer than 20-feet and allow ample wire to remove the receiver for annual battery replacement.
WALL MOUNTING
First, install (4) AA-size 1.5 ALKALINE batteries in the remote receiver (Fig 11). For best performance, remote receiver
batteries should be factory fresh when installed. The system operates best when battery output is greater than 5.3 volts.
Four (4) new AA batteries should provide an output voltage of 6.0 to 6.2 volts. Be sure batteries are installed with the
(+) and (-) ends facing the correct direction.
Next, attach wall mount cover plate to receiver box (Fig. 12):
Position the receiver as shown in the diagram to the left with lower tab on wall mount cover plate inserted into groove of
receiver. Move the receiver up and snap into top tab of cover plate.
Position the cover plate so the word ON is facing up (Fig. 13); then, install the remote receiver into the plastic switch box
using the two long screws provided. Push the slide button over the receiver slide switch only after making sure the remote
receiver has LEARNED the transmitter’s security code (see LEARNING TRANSMITTER TO RECEIVER).
Skytech: 3002
REV. 4-19-12 Page 4
Remote Receiver
Cover Plate
(Rear View)
Fig. 12. Wall plate to Receiver
Fig. 13. Installing receiver into switch box.
R
E
M
O
T
E
ON
OFF
LEARN
W
ALL
Plastic Switch Box
Cover Plate
Receiver
Slide
Button
… 4 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Skytech 3002 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Skytech 3002 in the language / languages: English as an attachment in your email.

The manual is 1,04 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info