603162
5
Zoom out
Zoom in
Previous page
1/10
Next page
NOTE: The remote receiver will only respond to the transmitter when the 3-position slide button on the remote receiver is
in the (middle) REMOTE position. If the system does not respond to the battery transmitter on initial use, see LEARNING
TRANSMITTER TO RECEIVER section, and re-check battery positions in the remote receiver.
HEARTH MOUNT
The remote receiver can be placed on the replace hearth or under the replace, behind the control access panel or
louvers. Position where the ambient temperature inside the receiver case does not exceed 130°F. NOTE: The black Slide
Button (included) should be installed on the receiver for Hearth Mount applications.
WIRING INSTRUCTIONS
A qualied electrician or a gas technician who is trained with gas appliances and gas valves that will be operated by this
remote should install the remote control system. Incorrect wiring connections WILL cause damage to the gas valve or
electronic module operating the gas appliance and may also damage the remote receiver.
WIRING MILLIVOLT VALVES
The remote receiver must be connected to the millivolt valve at the
TH & TH/TP (thermostat) terminals on the terminal block on the
millivolt gas valve. Connect 18 gauge stranded or solid wires from
the remote receiver to the gas valve.
Operation of the remote receiver is similar to that of a thermostat in
that both turn the gas valve ON and OFF based on input signals. A
thermostat’s input signals are different temperatures. The remote
receiver’s input signals come from the transmitter.
Connect one black wire to the TH terminal and the other black wire to the TH/TP terminals on the millivolt gas valve. Nor-
mally it does not matter which wires go to which terminal (Fig. 14).
WIRING ELECTRONIC SPARK IGNITIONS
The remote control receiver can be connected, in series, to
a 24VAC transformer to the TR (transformer) terminal on the
ELECTRONIC MODULE. Connect the hot wire from the 24VAC
transformer to either of the wire terminals on the remote receiver.
Connect another wire (not included) between the other receiver
wire terminal and the TH (thermostat) terminal on the
ELECTRONIC MODULE (Fig. 15).
!
Fig. 14 Millivolt Gas Valve Wiring
!
Fig. 15 Electronic Spark Wiring
Skytech: 3002
REV. 4-19-12 Page 5
LEARNING TRANSMITTER TO RECEIVER
Each transmitter uses a unique security code. It will be necessary to press the LEARN button on the receiver to accept
the transmitter security code upon initial use, if batteries are replaced, or if a replacement transmitter is purchased from
your dealer or the factory. In order for the receiver to accept the transmitter security code, be sure the slide button on
the receiver is in the REMOTE position; the receiver will not LEARN if the slide switch is in the ON or OFF position. The
LEARN button in located on the front face of the receiver; inside the small hole labeled LEARN. Using a small screw-
driver or end of a paperclip gently press and release the black LEARN button inside
the hole. When you release the LEARN button the receiver will emit an audible
“beep”. After the receiver emits the beep press the transmitter MODE button and
release. The receiver will emit several beeps indicating that the transmitter’s code has
been accepted into the receiver.
The microprocessor that controls the security code matching procedure is controlled
by a timing function. If you are unsuccessful in matching the security code on the rst
attempt, wait 1-2 minutes before trying again – this delay allows the microprocessor to
reset its timer circuitry – and try up to two or three more times.
OFF
REMOTE
ON
LEARN
Fig. 16 Learning
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Skytech 3002 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Skytech 3002 in the language / languages: English as an attachment in your email.

The manual is 1,04 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info