603162

Skytech 3002 Manual

9
Zoom out
Zoom in
Previous page
1/10
Next page
Skytech: 3002
REV. 4-19-12 Page 9
CHILDPROOF “LOCK-OUT” – (CP)
This SKYTECH remote control includes a CHILDPROOF “LOCK-OUT” feature that allows the user to “LOCK-OUT”
operation of the appliance, from the TRANSMITTER.
SETTING “LOCK-OUT” – (CP)
1. To activate the “LOCK-OUT” feature, press and hold the UP
and TIMER/TIME buttons, together, for 5 seconds. The letters
CP will appear in TEMP frame on the LCD screen (Fig. 21).
2. To disengage the “LOCK-OUT”, press and hold the UP and
TIMER buttons, together for 5 seconds or more, and the
letters CP will disappear from the LCD screen and the
transmitter will return to its normal operating condition.
NOTE: If the appliance is already operating in the ON or
THERMO MODES, engaging the “LOCK-OUT” will not cancel the operating MODE. Engaging the “LOCK-OUT” prevents
only the manual operation of the TRANSMITTER. If in the auto modes, the THERMO operation will continue to operate
normally. To totally “LOCK-OUT” the operation of the
TRANSMITTER’S operating signals; the transmitter’s MODE must be set to OFF.
ROOM
SET
Fig. 21 Child Protection (CP)
MODE
TIMER
TIME
SET
BATTERY LIFE
Life expectancy of alkaline batteries should be at least 12-months. Check and replace all batteries annually. When the
Transmitter no longer operates the receiver from a distance it did previously (i.e., the transmitter’s range has decreased)
or the remote receiver does not function at all, the batteries should be checked. It is important that the remote receiver
batteries are fully charged, providing a combined output voltage of at least 5.3 volts. The length of the wire between the
remote receiver and the gas valve directly affects the operating performance of the remote system. The longer the wire,
the more battery power is required to deliver signals between the remote receiver and the gas valve. The Transmitter
should operate with as little as 2.5 volts of battery power, measuring at the (2) 1.5-volt batteries.
TROUBLE SHOOTING
Should you encounter problems with your replace system, the problem may be with the replace itself or it could be with
the SKYTECH remote control. Review the replace manufacturer’s operation manual to make sure all connections are
properly made. Then check the operation of the SKYTECH remote in the following manner:
1. Make sure receiver batteries are installed properly. If one battery is installed backward, receiver will not operate in
remote mode. Be sure battery output is 2.5 volts or more. (Slide switch is independent of battery condition.)
2. Be sure the transmitter’s batteries are properly installed and that the battery output is 2.5 V or more.
3. Check to make sure the transmitter is communicating with the receiver.
• If the receiver beeps when the MODE button is depressed on the transmitter they are communicating.
Note: The receiver only beeps in ON & OFF modes. No beeping occures from ON to Thermo mode.
• If the receiver does not beep when the MODE button is depressed on the transmitter, you will need to “learn”
(teach) the receiver the code of the transmitter. See page 5 Learning Transmitter to Receiver section.
4. Make sure the transmitter is within the 15 to 20-foot range of the receiver.
5. Positioning of the receiver is important. If the receiver is “enclosed” in a metal surround, the operation of the
receiver may be affected as noted below. Reposition the receiver to improve operating range. It is suggested that a
heat shield be installed to protect the receiver from extreme heat. If the receiver is “enclosed” in a metal surround, this
can:
• Cause the RF signal to get lost and not communicate with the receiver.
• Cause the working distance to be shorter than normal.
… 9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Skytech 3002 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Skytech 3002 in the language / languages: English as an attachment in your email.

The manual is 1,04 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info