603162

Skytech 3002 Manual

8
Zoom out
Zoom in
Previous page
1/10
Next page
Skytech: 3002
REV. 4-19-12 Page 8
SETTING THE TEMPERATURE SWING (TEMPERATURE DIFFERENTIAL)
1. To change the temperature “SWING” setting (1-3), press the TIMER/TIME and DOWN buttons simultaneously (Fig. 18)
to display the current “SWING” setting in the SET TEMP frame. The letter “S” will display in the ROOM TEMP frame
on the LCD screen.
2. Press the UP or DOWN button to change the temperature differential or “SWING” (1-3). See above for 1-3 “SWING”
temperature valves.
3. To store the “swing number press the SET button or allow 15 seconds to lapse, and the new “swing number’ will be
automatically programmed.
MANUAL CHECK OF “ SWING” OR TEMPERATURE DIFFERENTIAL
The operation of the factory set “THERMO SWING” can be
checked by adjusting the SET temperature 2° F above or below
the room temperature. This will cause the system to turn ON
or OFF. Normally the system will only respond to temperature
changes every two minutes. Manually changing the SET tem-
perature will activate the system in less than 10 seconds. IF the
“SWING” is changed, then a new room temperature differential
will respond. Factory setting of “SWING”
temperature is 2° F.
ROOM
SET
Fig. 20 Low Battery Sign
ROOM
SET
Fig. 18. Setting Swing Temperature
MODE
TIMER
TIME
SET
SETTING THE COUNTDOWN TIMER
This remote control system can operate with a built-in countdown timer when the transmitter is in the ON or THERMO
modes only (THERMO or ON must be displayed on the screen).
1. Press and release the TIMER/TIME button on the transmitter.
The word TIMER will appear and 0:15 minutes will begin
blinking on the screen (Fig. 19).
2. Press the UP or DOWN button on the transmitter to begin
advancing through each of the countdown time options.
Available countdown times are 15 minutes, 30 minutes,
45 minutes, 1 hour, 1 hour 30 minutes, 2 hours,
2 hours 30 minutes, and each additional half-hour up to nine
(9) maximum hours.
3. To set the TIMER press the SET button on the transmitter if the
system is ON. It will remain ON until the time has expired. If
the system is in the THERMO mode, it will cycle on and off,
as the room temperature requires until the “time” has expired.
OPERATIONAL NOTE: When the timer is used in the THERMO mode, the THERMO operation will resume when the
“time” has expired.
ROOM
SET
Fig. 19 Setting Timer
MODE
TIMER
TIME
SET
LOW BATTERY INDICATOR
A low battery icon will be visible in the upper left corner of the LCD screen when
battery power has dropped signicantly (Fig. 20). At this time, approximately two weeks of
battery power remains until the transmitter may experience partial or complete loss of
functions.
… 8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Skytech 3002 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Skytech 3002 in the language / languages: English as an attachment in your email.

The manual is 1,04 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info