Manual Siemens ts 25 gp100 slider sl25 green power (page 12 of 102) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

324045

Zoom out

Zoom in

1/102

Cleaning & Maintenance

Always unplug the appliance from the mains supply

before carrying out any cleaning or maintenance

operation on it.

1. After ironing, pull out the plug and allow the appliance to

cool down before cleaning.

2. Wipe the housing, handle and iron body with a damp

cloth.

3. If the soleplate is soiled with dirt or scale, clean it with a

damp cloth.

4. Never use abrasive products or solvents.

Storing the appliance (D)

1. Always allow the appliance to cool down before storing it.

2. Set the main power to the “0” position and disconnect the

mains cable.

3. Place the iron on the iron pad, standing on the soleplate.

4. Empty the water tank and store the mains cable on the

cord rewind facility. Tidy the steam hose on the handle of

the iron using the cord clip provided (14*). Do not wrap the

cords too tight.

* Depending on the model.

Fabric protection soleplate

cover (E)

(depending on the model)

The fabric-protection soleplate cover is used for steam-

ironing delicate garments at maximum temperature without

damaging them. Use of the soleplate cover also does away

with the need for a cloth to prevent shine on dark materials.

It is advisable to ﬁrst iron a small section on the inside of the

garment to see if it is suitable.

To attach the soleplate cover to the iron, place the tip of the

iron into the end of the soleplate cover and pull the elastic

strap over the lower rear of the iron until it ﬁts tightly. To

release the soleplate cover, pull the elastic strap and remove

the iron.

The fabric-protection soleplate cover may be purchased from

the customer service or specialist shops:

Accessory code

(After-sales)

Name of accessory

(Specialist outlets)

464847 TZ25100

464848* TZ25200*

571510** TZ20450**

* Cork handle iron

** Only for model TS25430

“Calc‘n clean” (F)

Cleaning the Boiler

To extend the life of your steam generator and to avoid any

build up of scale, it is essential that you rinse out the boiler

after several hours of use (approximately after 50 hours). If

the water is hard, increase the frequency.

Do not use descaling agents for rinsing out the boiler, as they

could damage it.

1. Check that the appliance is cold and unplugged for more

than 2 hours, and that the removable water tank (1) is

empty.

2. Place your appliance on the edge of your kitchen sink.

3. Remove the plastic cover located on the bottom of the

appliance by turning it to the

position.

4. Unscrew the boiler drainage plug located on the bottom of

the appliance using a coin.

5. Holding your steam generator in upside down position,

and using a jug, ﬁll the boiler (in the base unit) with 1/4 litre

of water

6. Shake the base unit for a few moments and then empty it

completely over a sink or bucket. To obtain the best result,

we recommend that this operation is done twice

Important: before re-closing, make sure no water remains

in the boiler.

7. Replace and tighten up the boiler drainage plug with a

coin.

8. Insert and close the plastic cover by turning it to the

position.

Automatic clean warning

(depending on model)

Pilot light (3) will ﬂash indicating that boiler must be rinsed. To

do this, follow the procedure described in the section above.

To reset “Calc‘n clean” pilot light and counter, switch the

station off twice, keeping it off during at least 30 seconds

each time

Rinsing the iron steam chamber (G)

This procedure helps to remove scale particles out of the

steam chamber.

Carry it out approximately every 2 weeks, if the water in your

area is very hard.

a) Ensure that the iron is cooled down.

b) Set the temperature selector (10) of the iron to the “min”

position.

c) Fill the tank with tap water.

d) Plug in the mains cable and set the main power switch (6)

to the “I” position.

e) Wait until the “steam ready” indicator lamp (7) lights up.

f) If the steam station has steam regulator (4), set it to the

maximum position (“10”).

g) Hold the iron over the sink or a container to collect the

water.

h) Press the steam release button (11) and gently shake

the iron. Boiling water and steam will come out, carrying

scale and or deposits that might be there. This could take

approximately 5 minutes.

i) Set the temperature selector (10) of the iron to the “max”

position, without pressing the steam release button (11).

The water in the steam chamber will start evaporating.

Wait until all the water inside the chamber has been

evaporated.

j) To clean the soleplate, immediately rub off any residue by

running the hot iron over dry cotton cloth.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Siemens ts 25 gp100 slider sl25 green power in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,96 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Siemens ts 25 gp100 slider sl25 green power Manual

Product: