735538
7
Zoom out
Zoom in
Previous page
1/14
Next page
Display modes
In DISPLAY MODE the DEFAULT operation is that the sensor alternates between carbon dioxide and
carbon monoxide readings presentation. The push button MENU(+) is used to select the indicated
value on the display to be the error code or the set points of temperature and CO
2
After power up the
display will always return to the Default display mode. If a permanent change of default values is
requested the PC software is to be used.
Function
Line
Display
Time
limit
Function description
0
CO / CO
2
no
DEFAULT - Normal operation
1
Exxx
yes
Error code. If no error has been detected the code E0 is shown. The
error code is reset with Entr(+-).
2
Present CO
and CO
2
.
set points
no
Toggle between display of temperature and CO
2
set point with
MENU(+).
Table III. On the display without entering the maintenance menu
Maintenance level
A number of execution options are available from the MAINTENANCE MENU (see Table IV). This level
is accessed only from the display mode in the set points of CO and CO
2
selection. A two buttons push
and an access code restrict access, intended for competent trained service personnel only. The Entr(+-
)command is done by PUSHING MENU AND ESC AT THE SAME TIME (hold down for about 14
seconds). The access code has eight binary digits; one press at MENU(+) equals 1 and one press at
ESC(-) equals 0. The code value can be changed for your personal choice from the software UIP 4.3.
Always use the ESC button to return to the DEFAULT mode. Several pushes of the ESC button may
be needed to return to the DEFAULT mode. The Entr(+-) push (MENU & ESC) eventually leads to
execution of functions, which causes temporary or permanently change of any parameter, that affects
the system outputs!
Function
Line
Display
Time
limit
Function description
3
ECxx
yes
Access code to the service menu The default value of the code is
255 (=11111111, that is eight presses on MENU(+)). Press down
MENU(+) and let it scroll until it stops. The last two digits of the code
are shown. Then ENTER to accept the selected code.
4a
SPCO
yes
For setting the set point of the CO concentration.
4b
The present
CO set point
yes
For increase / decrease of the CO set point. The set point is
increased by stepping with MENU(+) button. Decreasing is done by
stepping with the ESC(-) button.
5a
SPc
yes
For setting the set point of the CO
2
concentration
5b
The present
CO
2
set point
yes
For increase / decrease of the CO
2
-concentration set point The
set point is increased by stepping with MENU(+) button. Decreasing
is done by stepping with the ESC(-) button.
6a
AOUt
yes
First step of adjusting the analogue outputs MAX and MIN values
6b
An xx
no
Select analogue output by stepping with MENU(+) button
6c1
SetL
no
Leads to adjustment of the MIN value.
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Senseair aSENSE M III at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Senseair aSENSE M III in the language / languages: English as an attachment in your email.

The manual is 1,48 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Senseair aSENSE M III

Senseair aSENSE M III Installation Guide - English - 3 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info