782162

Scheppach SB08 Woodster Manual

29
Zoom out
Zoom in
Previous page
1/48
Next page
29
zone commerciale, utiliser un système d’aspiration qui
répond aux prescriptions commerciales.
• Lorsque la machine n’est pas en service, par example
à la fin du travail, détendre le ruban. Apposer une note
sur la machine demandant au prochain utilisateur de
retendre le ruban.
• Rassembler les rubans non utilisés (voir page 6) et les
conserver en un endroit sec. Avant l’utilisation, vérifier
qu’ils ne présentent pas de défauts (dents, criques).
Ne pas utiliser les rubans défectueux!
• Porter des gants appropriés pour manier les rubans.
Avant le commencement du travail, tous les disposi-
tifs de protection et de sécurité doivent être montés
sur la machine.
• Ne jamais nettoyer le ruban ou le guideruban avec une
brosse tenue à la main ou avec un racloir pendant que
le ruban est en marche. Les rubans recouverts d’une
couche de résine sont un danger pour la sécurité et
doivent être nettoyés régulièrement.
• Pour votre propre protection, porter des lunettes de
protection et des protègeoreilles. Porter un filet si vous
avez les cheveux longs.
• Retrousser les manches flottantes sur les coudes.
• Lors du travail, positionner toujours le guideruban le
plus près possible de la pièce. Veiller à avoir un éclai-
rage suffisant dans l’aire de travail 20 français et aux
abords de l’aire de travail.
• Pour des coupes droites, utiliser toujours la butée
longitudinale pour empêcher que la pièce bascule ou
glisse. Pour couper des pièces étroites avec avance
manuelle, utiliser le poussoir.
• Pour des coupes diagonales, placer la table dans la
position correspondante et guider la pièce sur la bu-
tée longitudinale. Pour couper des tenons et mortaises
en queue d’aronde ou bien des coins, incliner la table
dans la position désirée et bloquer celle-ci. Veiller à
avoir un guidage sûr de la pièce.
• Tenir la pièce de bois dans une zone sûre. Pour les
coupes répétitives, irrégulieres ou en arc, utiliser un
gabarit. Lorsque vous coupez des pièces rondes, as-
surezvous que la pièce ne peut pas rouler. Pour des
coupes transversales, utiliser l’accessoire „Gabarit de
coupe transversale“.
m Raccordement électrique
Le moteur électrique qui est installé est raccordé en or-
dre de marche.
Le raccordement électrique que doit effectuer le client
ainsi que les cables de rallonge utilisés doivent corres-
pondre aux normes en vigueur. Les branchements et
réparations de l’équipement électrique ne doivent être
effectués que par un spécialiste de l’électricité.
commercial regulations must be used for suction in
commercial areas.
• Loosen the sawband when the machine is not in op-
eration (e.g. after finishing work). Attach a notice on
the tension of the saw band to the machine for the
next user.
• Collect unused sawbands and store them safely in a
dry place. Check for faults (teeth, cracks) before use.
Do not use faulty sawbands!
• Wear suitable gloves when handling sawbands. All pro-
tective and safety devices must be securely mounted
on the machine before beginning work.
• Never clean the sawband or the sawband guide with a
hand-held brush or scraper while the sawband is run-
ning. Resincovered sawbands impair working safety
and must be cleaned regularly.
• For your own protection, wear protective glasses and
hearing protection. Wear a hairnet if you have long
hair.
• Roll up loose sleeves over the elbows.
• Always position the sawband guide as near the work-
piece as possible when working. Insure sufficient light-
ing in the work area and around the machine.
• Always use the fence for straight cuts to keep the work-
piece from tipping or slipping away. When working on
narrow workpieces with manual feed, use the push
stick.
• For diagonal cuts, place the saw bench in the appro-
priate position and guide the workpiece on the fence.
Insure safe workpiece guidance. For arced and irregu-
lar cuts, push the workpiece evenly using both hands
with the fingers together. Hold the workpiece with your
hands on a safe area.
• Use a pattern for repeated arced or irregular cuts. In-
sure that the workpiece does not roll when cutting
round pieces.
• Use the traverse cutting gauge special accessory for
safety when making traverse cuts.
m Electrical Connection
The installed electric motor is connected and is ready to
work.
The connection complies with the relevant VDE and DIN
regulations.
The customer-side mains supply and the used extension
line must meet these regulations.
Installations, repair, and maintenance work relating to
the electric installation may only be performed by spe-
cialists.
… 29 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach SB08 Woodster at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach SB08 Woodster in the language / languages: English, German, French, Italian as an attachment in your email.

The manual is 3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info