Manual Scheppach MS216A Kity (page 25 of 44) (English, German, French)

782498

Zoom out

Zoom in

1/44

25GB

the art and the recognised technical safety require-

ments. However, individual residual risks can arise

during operation.

• Health hazard due to electrical power, with the use of

improper electrical connection cables.

• Furthermore, despite all precautions having been met,

some non-obvious residual risks may still remain.

• Residual risks can be minimised if the „safety instruc-

tions“ and the „Proper use“ are observed along with

the whole of the operating instructions.

• Do not load the machine unnecessarily: excessive

pressure when sawing will quickly damage the saw

blade, which results in reduced output of the machine

in the processing and in cut precision.

• When cutting plastic material, please always use

clamps: the parts which should be cut must always

be xed between the clamps.

• Avoid accidental starting of the machine: the operat-

ing button may not be pressed when inserting the plug

in an outlet.

• Use the tool that is recommended in this manual.

In doing so, your mitre saw provides optimal perfor-

mance.

• Hands may never enter the processing zone when

the machine is in operation. Release the handle but-

ton and switch off the machine prior to any operations.

7. Before starting the equipment

• The equipment must be set up where it can stand

securely, i.e. it should be bolted to a workbench, a

universal base frame or similar. Use the holes in the

frame of the machine.

• All covers and safety devices have to be properly t-

ted before the equipment is switched on.

• It must be possible for the blade to run freely.

• When working with wood that has been processed

before, watch out for foreign bodies such as nails or

screws, etc.

• Before you press the ON/OFF switch check that the

saw blade is tted correctly. Moving parts must run

smoothly.

• Before you connect the equipment to the power sup-

ply make sure the data on the rating plate are denti-

cal to the mains data.

8. Attachment and operation

8.1 Attaching the saw (Fig. 1-6)

• To adjust the rotary table (16), push the locking lever

(13) downwards and pull the lower indexed position

lever (12) upwards with your index nger.

• Rotate the rotary table (16) and pointer (14) to the

desired angle on the scale (15) and lock in place by

folding up the locking lever (13).

• Pressing the machine head (5) lightly downwards

and removing the locking bolt (24) from the motor

bracket at the same time disengages the saw from

the lowest position.

• Swing the machine head (5) up until the release le-

ver (3) latches into place.

• It is possible to secure the clamping device (8) to

the left or right on the stationary saw bench (17).

• Attach the workpiece supports (9) to the xed saw

table (17) as shown in Figure 6a,b,c and push all the

way through. Secure the shafts with the retaining

springs to prevent them from slipping out accidental-

ly. The fasten in the desired position with the screw

(10).

• It is possible to tilt the machine head (5) a max. 45°

to the left by loosening the set screw (22).

8.2 Precision adjustment of the stop for crosscut

90° (Fig. 3,5,18)

• No stop angle included.

• Lower the machine head (5) and secure using the

locking bolt (24).

• Loosen the set screw (22).

• Position the angle stop (a) between the saw blade

(7) and the rotary table (16).

• Slacken the counternut (d). Adjust the adjusting

screw (30) until the angle between the saw blade (7)

and rotary table (16) is 90°.

• Retighten the counternut (d) to secure this setting.

• Subsequently check the position of the angle indi-

cator. If necessary loosen the pointer (20) using a

Philips screwdriver, set to position 0° on the angle

scale (19) and re-tighten the retaining screw.

8.3 Precision adjustment of the stop for mitre cut 45°

(Fig. 1,3,5,19)

• No stop angle included.

• Lower the machine head (5) and secure using the

locking bolt (24).

• Fix the rotary table (16) in the 0° position.

• Loosen the set screw (22) and use the handle (1) to

angle the machine head (5) 45° to the left.

• 45° - position angle stop (b) between the saw blade

(7) and rotary table (16).

• Slacken the counternut (c). Adjust the adjusting

screw (31) until the angle between the saw blade (7)

and rotary table (16) is precisely 45°.

• Retighten the counternut (d) to secure this setting.

8.4 Cross cut 90° and turntable 0° (Fig.1,2,6,7)

In the case of cutting widths up to approx. 100 mm it

is possible to x the traction function of the saw with

the set screw (23) in the rear position. In this position

the machine can be operated in cross cutting mode. If

the cutting width is over 100 mm then it is necessary

to ensure that the set screw (23) is loose and the ma-

chine head (5) can move.

Attention! For 90° mitre cuts, the moveable stop rail

(28) must be xed in the inner position.

• Open the set screw (29) on the moveable stop rail

(28) and push the moveable stop rail (28) inwards.

• The moveable stop rail (28) must be locked in a po-

sition far enough from the inner position that the dis-

tance between the stop rail (28) and the saw blade

(7) is no more than 5 mm.

• Before making the cut, check that no collision could

occur between the stop rail (28) and the saw blade

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach MS216A Kity in the language / languages: English, German, French as an attachment in your email.

The manual is 3.68 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach MS216A Kity Manual

Product: