Manual Scheppach MS216A Kity (page 27 of 44) (English, German, French)

782498

Zoom out

Zoom in

1/44

27GB

• Check the setting by completing a test cut.

8.9 Sawdust bag (Fig. 2)

The saw is equipped with a debris bag (21) for saw-

dust and chips.

Squeeze together the metal ring on the dust bag and

attach it to the outlet opening in the motor area.

The debris bag (21) can be emptied by means of a zip-

per at the bottom.

8.10 Changing the saw blade (Fig. 11-15)

Remove the power plug!

Important.

Wear safety gloves when changing the saw blade.

Risk of injury!

• Remove the spring (41) from the pin by pushing to-

gether the two ends.

• Release the guide bar (40) from the pin.

• Firmly press the saw shaft lock (4), and slowly turn

the ange screw (32) clockwise. After max. one turn,

the saw shaft lock (4) engages.

• Then undo the ange screw (32), by applying a

slightly greater force in a clockwise direction.

• Fully unscrew the ange screw (32) and remove the

outer ange (33).

• Press the unlocking lever (3) to slide back the saw

blade guard (6), then remove the saw blade (7) from

the inner ange (39) and pull out in a downwards

direction.

• Carefully clean the ange screw (32), outer ange

(33) and inner ange (39).

• Insert the new saw blade (7) in the reverse se-

quence and tighten.

• Position the guide bar (40) on the pin again, and se-

cure with the spring (41).

• Important! The cutting angle of the teeth, in other

words the direction of rotation of the saw blade (7)

must coincide with the direction of the arrow on the

housing.

• Before continuing your work make sure that all safe-

ty devices are in good working condition.

• Important! Every time that you change the saw

blade (7), check to see that it spins freely in the ta-

ble insert (11) in both perpendicular and 45° angle

settings.

• Important! The work to change and align the saw

blade (7) must be carried out correctly.

8.11 Using the laser (Fig. 16,17)

• To switch on: Move the ON/OFF switch of the laser

(35) to the “1” position. A laser line is projected onto

the material you wish to process, providing an exact

guide for the cut.

• To switch off: Move the ON/OFF switch of the laser

(35) to the “0” position.

• Replacing the battery: Switch off the laser (34).

Remove the battery compartment cover (37). Re-

move the batteries and replace with new batter-

ies (3 x AG13) Check that the battery terminals are

positioned correctly when inserting new batteries.

Close the battery compartment (36) again.

8.12 Changing the speed (Fig. 2)

The saw has 2 speed ranges:

langsam schnell

vitesse lente vitesse rapide

slow fast

Pomalu rychle

Pomalý rýchly

Počasnega hitrega

lassú gyors

бавно бързо

Nopea hidas

• To operate the saw at a speed of 3800 rpm (metal),

set the switch (42) to position I.

• To operate the saw at a speed of 5000 rpm (wood),

set the switch (42) to position II.

9. Transport (Fig. 1,2)

• Tighten the set screw (26) in order to lock the rotary

table (16)

• Activate the release lever (3), press the machine

head (5) downwards and secure with the safety pin

(24). The saw is now locked in its bottom position.

• Fix the saw’s drag function with the locking screw for

drag guide (23) in rear position.

• Carry the equipment by the xed saw table (17).

• When reassembling the equipment proceed as de-

scribed under section 7.1.

10. Maintenance

m Warning! Prior to any adjustment, maintenance or

service work disconnect the mains power plug!

General maintenance measures

Wipe chips and dust off the machine from time to time

using a cloth. In order to extend the service life of the

tool, oil the rotary parts once monthly. Do not oil the

motor.

When cleaning the plastic do not use corrosive prod-

ucts.

Brush inspection

Check the carbon brushes after the rst 50 operating

hours with a new machine, or when new brushes have

been tted. After carrying out the rst check, repeat the

check every 10 operating hours.

If the carbon is worn to a length of 6 mm, or if the spring

or contact wire are burned or damaged, it is necessary

to replace both brushes. If the brushes are found to be

usable following removal, it is possible to reinstall them.

11. Storage

Store the device and its accessories in a dark, dry and

frost-proof place that is inaccessible to children. The

optimum storage temperature is between 5 and 30˚C.

Store the electrical tool in its original packaging.

Cover the electrical tool in order to protect it from dust

and moisture.

Store the operating manual with the electrical tool.

12. Electrical connection

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach MS216A Kity in the language / languages: English, German, French as an attachment in your email.

The manual is 3.68 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach MS216A Kity Manual

Product: