Manual Scheppach KZS1500 Primaster (page 30 of 52) (English, German, French)

782502

Zoom out

Zoom in

1/52

30 | GB

• To switch o󰀨: Move the ON/OFF switch of the la-

ser (34) to the “0” position.

• Replacing the battery: Switch o󰀨 the laser (33).

Remove the battery compartment cover (36). Re-

move the batteries and replace with new batteries

(2 x 1.5 Volt Type LR 03 Micro, AAA) Check that

the battery terminals are positioned correctly when

inserting new batteries. Close the battery compart-

ment (35) again.

8.12 Adjusting the laser (Fig. 21)

If the laser (33) ceases to indicate the correct cutting

line, you can readjust the laser. To do so, open the

screws (38) and set the laser by moving sideways to

that the laser beam strikes the teeth of the saw blade

(6).

9. Transport

• Tighten the set screw (26) in order to lock the rotary

table (14)

• Activate the release lever (3), press the machine

head (4) downwards and secure with the safety pin

(23). The saw is now locked in its bottom position.

• Fix the saw’s drag function with the locking screw

for drag guide (20) in rear position.

• Carry the equipment by the xed saw table (15).

• When reassembling the equipment proceed as de-

scribed under section 7.

10. Maintenance

m Warning! Prior to any adjustment, maintenance

or service work disconnect the mains power plug!

General maintenance measures

Wipe chips and dust o󰀨 the machine from time to time

using a cloth. In order to extend the service life of the

tool, oil the rotary parts once monthly. Do not oil the

motor.

When cleaning the plastic do not use corrosive prod-

ucts.

Brush inspection

Check the carbon brushes after the rst 50 operat-

ing hours with a new machine, or when new brushes

have been tted. After carrying out the rst check,

repeat the check every 10 operating hours.

If the carbon is worn to a length of 6 mm, or if the

spring or contact wire are burned or damaged, it is

necessary to replace both brushes. If the brushes

are found to be usable following removal, it is possi-

ble to reinstall them.

8.9 Sawdust bag (Fig. 1)

The saw is equipped with a debris bag (17) for

sawdust and chips.

Squeeze together the metal ring on the dust bag

and attach it to the outlet opening in the motor area.

The debris bag (17) can be emptied by means of a

zipper at the bottom.

8.10 Changing the saw blade (Fig. 15/16/17/18)

Remove the power plug!

Important.

Wear safety gloves when changing the saw

blade. Risk of injury!

• Swing up the machine head (5).

• Undo the screw (e) on the guide bar (37), so that it

can move freely and be pivoted downwards.

• Press the release lever (3). Swing up the saw blade

guard (6) to the point where the recess in the saw

blade guard (6) is above the ange bolt (31).

• Press the saw shaft lock (4) with one hand. With the

other hand insert the allen key (d) in the ange bolt

(31).

• Hold the Allen key (d) and slowly close the saw

blade guard until it touches the Allen key.

• Firmly press the saw shaft lock (4) and slowly ro-

tate the ange bolt (31) in clockwise direction. The

saw shaft lock (4) engages after no more than one

rotation.

• Now, using a little more force, slacken the ange

bolt (31) in the clockwise direction.

• Turn the ange screw (31) right out and remove the

external ange (32).

• Take the blade (7) o󰀨 the inner ange (38) and pull

out downwards.

• Carefully clean the ange screw (31), outer ange

(32) and inner ange (38).

• Fit and fasten the new saw blade (7) in reverse or-

der.

• Important! The cutting angle of the teeth, in other

words the direction of rotation of the saw blade (7)

must coincide with the direction of the arrow on the

housing.

• Move the guide bar (37) into position and tighten

the screw (e) again.

• Before continuing your work make sure that all

safety devices are in good working condition.

• Important! Every time that you change the saw

blade (7), check to see that it spins freely in the

table insert (11) in both perpendicular and 45° angle

settings.

• Important! The work to change and align the saw

blade (7) must be carried out correctly.

8.11 Using the laser (Fig. 3/19/20)

• To switch on: Move the ON/OFF switch of the la-

ser (34) to the “1” position. A laser line is projected

onto the material you wish to process, providing an

exact guide for the cut.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach KZS1500 Primaster in the language / languages: English, German, French as an attachment in your email.

The manual is 5.19 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach KZS1500 Primaster Manual

Product: