Manual Scheppach KZS1500 Primaster (page 28 of 52) (English, German, French)

782502

Zoom out

Zoom in

1/52

28 | GB

8.3 Cross cut 90° and turntable 0° (Fig.8)

In the case of cutting widths up to approx. 100 mm

it is possible to x the traction function of the saw

with the set screw (20) in the rear position. In this

position the machine can be operated in cross cut-

ting mode. If the cutting width is over 100 mm then

it is necessary to ensure that the set screw (20) is

loose and the machine head (4) can move.

Attention! For 90° cross cuts, the moveable stop

rail (16a) must be xed in the inner position.

• Open the set screw (16b) on the moveable stop rail

(16a) and push the moveable stop rail (28) inwards.

• The moveable stop rail (16a) must be locked in a

position far enough from the inner position that the

distance between the stop rail (16a) and the saw

blade (6) is no more than 8 mm.

• Before making the cut, check that no collision could

occur between the stop rail (16a) and the saw blade

(6).

• Tighten the set screw (16b) again.

• Move the machine head (4) to its upper position.

• Use the handle (3) to push back the machine head

(4) and x it in this position if required (dependent

on the cutting width).

• Place the piece of wood to be cut at the stop rail

(16) and on the turntable (14).

• Lock the material with the clamping device (7) on

the xed saw table (15) to prevent the material from

moving during the cutting operation.

• Push down the release lever (3) to release the ma-

chine head (4).

• Press the ON/OFF switch (2) to start the motor.

• With the drag guide (21) xed in place: use the han-

dle (1) to move the machine head (4) steadily and

with light pressure downwards until the saw blade

(6) has completely cut through the work piece.

• With the drag guide (21) not xed in place: pull

the machine head (4) all the way to the front.

Lower the handle (1) to the very bottom by ap-

plying steady and light downward pressure.

Now push the machine head (4) slowly and steadily

to the very back until the saw blade (6) has com-

pletely cut through the work piece.

• When the cutting operation is completed, move

the machine head (4) back to its upper (home)

position and release the ON/OFF button (2).

Attention! The machine executes an upward

stroke automatically due to the return spring, i.e.

do not release the handle (1) after completing the

cut; instead allow the machine head to move up-

wards slowly whilst applying light counter pressure.

• When working with wood that has been processed

before, watch out for foreign bodies such as nails

or screws, etc.

• Before you press the ON/OFF switch check that the

saw blade is tted correctly. Moving parts must run

smoothly.

• Before you connect the equipment to the power

supply make sure the data on the rating plate are

dentical to the mains data.

Do not use the tool if the switch does not allow

you to switch from the ON state to the OFF state.

8. Attachment and operation

8.1 Attaching the saw (Fig. 1/2/3/4/5)

• In order to adjust the rotary table (14) loosen the set

screw (26) approx. 2 turns.

• Turn the rotary table (14) and pointer (12) to the

desired angle measurement on the scale (13) and

secure with the set screw (26).

• Pressing the machine head (4) lightly downwards

and removing the locking bolt (23) from the motor

bracket at the same time disengages the saw from

the lowest position.

• Swing the machine head (4) up until the release le-

ver (3) latches into place.

• It is possible to secure the clamping device (7) to

the left or right on the stationary saw bench (15).

Insert the clamping device (7) in the hole on the

rear side of the stop rail (16) and secure it with the

star grip screw (7a).

• Attach the workpiece supports (8) to the xed saw

table (15) as shown in Figure 5 and fasten with the

screw (9).

• It is possible to tilt the machine head (4) a max. 45°

to the left by loosening the set screw (22).

8.2 Precision adjustment of the stop for cross-

cut 90° (Fig. 1/6/7)

• No stop angle included.

• Lower the machine head (4) and secure using the

locking bolt (23).

• Loosen the set screw (22).

• Position the angle stop (a) between the saw blade

(6) and the rotary table (14).

• Adjust the adjusting screw (27) until the angle be-

tween the saw blade (6) and rotary table (14) is 90°.

It is not necessary to x this setting because it is

maintained by the spring pretension. Subsequently

check the position of the angle indicator. If necessary

loosen the pointer (19) using a Philips screwdriver, set

to position 0° on the angle scale (18) and re-tighten

the retaining screw.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach KZS1500 Primaster in the language / languages: English, German, French as an attachment in your email.

The manual is 5.19 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach KZS1500 Primaster Manual

Product: