Manual Scheppach KS55PS Kity (page 22 of 72) (English, German, French, Italian, Portuguese, Spanish)

782280

Zoom out

Zoom in

1/72

22 GB

Only a qualied electrician is permitted to connect the

machine and complete repairs on its electrical equip-

ment.

In the event of enquiries please specify the following

data:

• Motor manufacturer

• Type of current of the motor

• Data recorded on the machine’s rating plate

• Data recorded on the switch’s rating plate

13. Maintenance

If specialist personnel must be brought in for extraor-

dinary service or repairs during the warranty period

and thereafter, please contact a service provider rec-

ommended by us or contact the manufacturer directly.

Overhauls, maintenance work, cleaning, as well as

the elimination of any malfunctions must only be un-

dertaken after turning off the motor.

All protective and safety equipment must be rein-

stalled immediately upon completion of any repair or

maintenance work.

Regular maintenance

The regular maintenance decribed above and in the

paragraph below can be carried out by unskilled per-

sonnel.

Do not oil the plunge cut saw, cause cutting must be

carried out in dry conditions; all rotating parts are self-

lubricating.

During maintenance, wear protective gear if possible

(accident-prevention goggles and gloves).

Remove cuttings when necessary both from the cut-

ting area, work surfaces and support bases.

Use of an aspirator or brush is recommended.

ATTENTION: Do not use compressed air jets!

Regularly check blade conditions: if difculties should

arise during cutting, have it sharpened by skilled per-

sonnel or replace it if necessary.

Assistence

When in need of skilled personnel for special main-

tenance, or for repairs, both during and following the

guarantee period, always apply to authorized centres

for assistance or directly to the manufacturer if there

is no authorized centre in your area.

Service information

Please note that the following parts of this product are

subject to normal or natural wear and that the following

parts are therefore also required for use as consumable.

Wear parts*: Carbon brushes, saw blade

* Not necessarily included in the scope of delivery!

Cutting with rails

1. Place the machine in the guide rails. can be read-

justed using the hex driver included in the deliv-

ery, when there is the risk of the adjusting screws

releasing by themselves.

2. Turn on the machine by pressing the on/off switch

(4).

3. Press the dip trigger (3).

4. Press the saw downwards to reach the sawing

depth. During rst use the rubber lip is sawn off

and thus splitter protection is guaranteed up to

the saw blade.

5. Push the saw uniformly forwards.

6. Turn off the machine and tilt the saw blade to the

top when the saw cutting is complete.

Sawing with dust suction

Connect the suction hose to the exhaust nozzle - Ø

38 mm (12).

12. Electrical connection

The installed electric motor is completely wired

ready for operation.

The customer’s connection to the power supply

system, and any extension cables that may be

used, must conform with local regulations.

Important remark:

The motor is automatically switched off in the event

of an overload. The motor can be switched on again

after a cool ing down period that can vary.

Defective electrical connection cables

Electrical connection cables often suffer insulation

dam age. Possible causes are:

• Pinch points when connection cables are run

through window or door gaps.

• Kinks resulting from incorrect attachment or laying

of the connection cable.

• Cuts resulting from running over the connecting ca-

ble.

• Insulation damage resulting from forcefully pulling

out of the wall socket.

• Cracks through aging of insulation.

Such defective electrical connection cables must not

be used as the insulation damage makes them ex-

tremely hazardous.

Check electrical connection cables regularly for dam-

age. Make sure the cable is disconnected from the

mains when checking.

Electrical connection cables must comply with the

applicable VDE and DIN provisions. Only use con-

nection cables with the marking „H05VV-F“.

The printing of the type designation on the connec-

tion cable is mandatory.

Single-phase motor

• The mains voltage must coincide with the voltage

specied on the motor’s rating plate.

• Extension cables up to a length of 25 m must have

a cross-section of 1.5 mm2.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach KS55PS Kity in the language / languages: English, German, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 4.31 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach KS55PS Kity Manual

Product: