Manual Scheppach KS55PS Kity (page 21 of 72) (English, German, French, Italian, Portuguese, Spanish)

782280

Zoom out

Zoom in

1/72

21GB

6. Screw in and tighten the saw blade locking screw

while keeping the shaft locking mechanism

pressed again.

7. Set the plunge saw to its original position.

Adjusting the splitting wedge, Fig. 7

Adjust the distance between saw blade and splitting

wedge after a saw blade replacement, or whenever

necessary.

Put the saw in the same position as you do when re-

placing a saw blade.

Unfasten the adjustment screw (18) using an Allen

key and set the splitting wedge 2-3 mm higher than

the saw blade, then retighten the adjustment screw.

11. Operations

After having performed all the above procedures and

opera tions, you may begin cutting.

ATTENTION:

Always keep hands away from the cutting area and

do not try to approach it when the machine is running.

Switching the product on/off, Fig. 1

To switch the plunge-cut saw on, press the on/off

switch (4). To switch off, release the on/off switch (4).

Operating and holding the plunge-cut saw, Fig. 8

1. Secure the work piece so that it cannot get dis-

placed or moved while sawing.

2. Only move the saw forwards.

3. Grip the saw tightly with both hands ensuring that

one hand is placed on the main handle and the

other on the front handle.

4. When using a guide rail, it must be fastened with

screw clamps.

5. Make sure the power cable is not placed in the

sawing direction.

Sawing

1. Place the front part of the machine onto the work

piece.

2. Switch the machine on using the on/off switch (4).

3. Press the plunge-cut trigger (3).

4. Push the saw downwards to reach the sawing

depth.

5. Push the saw forward evenly.

6. After nishing the sawing cut, switch the machine

off and move the saw blade upwards.

Plunge-cuts, Fig. 9

1. Place the saw onto the work piece.

2. Place the cutting indicator with the rear arrow (A)

on the marked plunge-cut position.

3. Switch the machine on and push the saw down-

wards until you reach the set cutting depth.

4. Move the saw forwards until the cutting indication

5. After completion of the plunge-cut, move the saw

blade upwards and switch the saw off.

9. Start-up

Observe the safety notes in the operating instructions

before operating the machine.

REMOVAL OF PACKAGING

Remove the box used to protect the machine during

trans portion and keep it intact for future transportation

and storage.

ELECTRICAL CONNECTIONS

Check that the electrical system to which the machine

is connected is earthed in compliance with current

safety regulations and that the current socket is in

perfect condition.

The electrical system must be tted with a magneto-

thermal protective device to safeguard all conductors

from short circuits and overload.

The selection of this device should be in line with the

following electrical specications of the machine stat-

ed on the motor.

10. ADJUSTING

Caution: Prior to carrying out one of the following ad-

justment steps, switch the machine off and unplug the

mains plug.

Cutting depth adjustment, Fig. 2

The cutting depth can be adjusted from 0 to 55 mm.

Unfasten the cutting depth adjustment screw (6) and

set the required depth using the scale (7) and retight-

en the screw.

The dimentions on the rail shows the cutting depth

without rail.

Mitre settings, Fig. 3

The mitre square can be set from 0° to 45°.

Unfasten the mitre adjustment screws (8) on both

sides, set the desired mitre square on the scale (9)

and retighten both screws.

Saw blade replacement, Fig. 4, 5, 6

Caution: Before you are going to make the saw

blade change, switch off the machine and un-

plug the power cord.

1. Press the plunge trigger (3), bring the saw blade

into the blade-change position (Adjustment screw

for depth of cut shall be adjusted to 25mm) and

insert the hex wrench into the blade locking

screw (17).

2. Press on the shaft lock (13) and rotate the saw

blade (11) until the lock clicks into place.

3. Hold down the locking shaft (13) and open the

blade locking screw (17) counter clockwise, while

keeping the blade in the blade-changing position.

4. Remove the outer ange (16) and the saw blade

(11).

(Caution: risk of injuries, wear protective gloves)

5. Insert the new blade and ange.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach KS55PS Kity in the language / languages: English, German, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 4.31 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach KS55PS Kity Manual

Product: