Manual Scheppach HSM3500 (page 31 of 92) (English, German, French, Spanish)

781910

Zoom out

Zoom in

1/92

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

GB | 31

6. Re-mount the saw blade guard (1).

7. Check the concentricity by briey starting up the

machine and then switching it off again.

Attention!

• Operation of the stone cutting machine is not per-

mitted without the corrective cover!

• When fastening the blade, make sure that the dia-

mond cutting wheel does not „wobble“.

• Ensure the rm seating of the water hoses on the

protective cover.

14. Transport (Fig. 23)

Caution! Disconnect power plug

Observe the following for transporting the stone cut-

ting machine:

• Lift off the roll slide (6) and transport it separately.

• Lock the cutting head unit (4).

• Empty the water tube (8) and cooling system.

• Fold the supporting feet (11) as described in (Fig.

4-7) and use the transport rollers for the transport.

15. Electric connection

Check electric cables regularly for damage. Ensure

that during the check, the connecting cable is not

connected to the mains.

Electric connecting cables must conform to the com-

mon VDE- and DIN provisions. Only use connecting

cables with the H 07 RN designation.

Keeping a copy of the type designation on the con-

necting cable is a specication

• The product meets the requirements of EN 61000-

3-11 and is subject to special connection condi-

tions. This means that use of the product at any

freely selectable connection point is not allowed.

• Given unfavorable conditions in the power supply

the product can cause the voltage to uctuate tem-

porarily.

• The product is intended solely for use at connec-

tion points that

a) do not exceed a maximum permitted supply im-

pedance “Z”, or

b) have a continuous current-carrying capacity of

the mains of at least 100 A per phase.

• As the user, you are required to ensure, in consulta-

tion with your electric power company if necessary,

that the connection point at which you wish to oper-

ate the product meets one of the two requirements,

a) or b), named above.

Damaged electric connecting cables

Insulation damages frequently occur on electric con-

necting cables. The reasons are:

• Pressure points, if connecting cables are routed

through window or door gaps.

1. Unscrew the star knob screw (e) on the cutting

head unit (4) and push the cutting arm upwards.

2. Fix the desired cutting depth with the star knob

screw (f).

3. Lower the cutting head unit (4) with the diamond

cutting wheel.

4. Leave the star knob screw (e) unscrewed.

Attention! It should be possible to lower the dia-

mond cutting wheel (14) approx. 3 mm below the

upper edge of the roll slide (6). The diamond cutting

wheel may not touch the roll slide.

Cutting with the cutting head – pivot device / mi-

tre cuts (Fig. 18-20)

Unscrew the cutting head pivot device with the lever

screw (d) and pivot the cutting head (4) 45° to the

stop. Re-tighten the lever.

Attention! Check the stop setting before you begin

cutting. The diamond cutting wheel may not touch

the roll slide.

Perform cutting as described.

Replacing the diamond cutting wheel (Fig. 21,22)

Attention! Pull out the mains plug

Caution!

• Danger of cuts on the diamond cutting wheel!

• Wear gloves when replacing the diamond cutting

wheel.

• Check the cutting wheel for direction of rotation,

concentricity and possible damage!

1. Pull out the mains plug.

2. Unscrew the star knob screw (e) on the cutting

head unit (4) and push the cutting arm upwards

completely. Lock the cutting arm with the star

knob (f) on the cutting head unit (4) (Fig. 15).

3. Unscrew and remove the four screws on the

blade‘s protective cover (1) and remove the pro-

tective cover. Note: It is not necessary to discon-

nect the water hose on the protective cover. Care-

fully fold the protective cover down.

4. Hold the cutting shaft in place with the supplied

Allen key and unscrew the clamping nut with the

open-ended spanner (included in the scope of

delivery). Left-handed thread! Carefully remove

the clamping nut, the pressure ange and the dia-

mond cutting wheel (14).

5. Before installing the new diamond cutting wheel

(14), clean the cutting shaft and the battery ange

with a rag or brush. Attention! Do not use any clean-

ing agents which can corrode the components.

Attention! When installing the new diamond cutting

wheel, proceed in the reverse sequence. Make sure

that the direction of rotation is correct! (Insert the

diamond cutting wheel – ARROW DIRECTION – in

the operating side on the ange holder). The arrow

direction on the cutting wheel and the protective cov-

er must match.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach HSM3500 in the language / languages: English, German, French, Spanish as an attachment in your email.

The manual is 6.7 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach HSM3500 Manual

Product: