Manual Scheppach HSM3500 (page 29 of 92) (English, German, French, Spanish)

781910

Zoom out

Zoom in

1/92

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

GB | 29

• Check the alignment of all moving parts, all bro-

ken or fastening parts, and all other conditions that

can affect smooth operation. Each damaged part

should be repaired or replaced by a technician im-

mediately.

• Do not use the machine if a switch cannot be ac-

tivated/deactivated correctly.

10. Operation

• Install the machine on an even, slide-proof oor.

• Check that the voltage on the nameplate matches

the existing voltage; connect the power plug to the

mains power supply only thereafter

• The cutting disc should be free to run before the

machine is switched on.

Caution: Cutting disc must always be cooled with

water.

Caution: Cutting disc runs with a time lag.

Do not break the cutting disc by applying pressure at

the sides.

• Under normal use conditions, the motor casing can

become hot.

• Do not use force on the machine or on an acces-

sory to achieve the performance of a bigger Indus-

trial machine. It does a better job at the output for

which it is designed.

• Dene all machine settings only when it is switched

off.

• Do not leave the machine unattended as long as

it is running.

• During shutdown, leave the machine only after it

comes to a complete standstill.

• Always switch the machine off before pulling out

the power plug from the mains socket.

• Always pull out the power plug. Never disconnect

the power plug from the mains socket by pulling

at the cable.

• Do not use cutting discs that do not meet the size

specications.

• Do not carry the machine by the cable.

Do not work with the machine if you are not sure

whether a working condition is safe of unsafe.

11. Assembly

Fig. 4-10

For packaging purposes, your machine is not fully

assembled.

1. Carefully remove the machine from the packaging

and set it aside on the ground.

2. First fold out the supporting foot (11) without trans-

port rollers up to the stop. Then lock the screw

upward in the oblong hole in order to x the foot

(Fig. 7, 8).

3. Repeat the process with the 2nd foot, with trans-

port rollers.

Do not wear loose clothing or ornaments which can

get entangled in rotating components.

Anti-skid shoes are recommended.

Protect long hair with suitable means.

Wear eye- and ear protection. Always wear:

• ANSI- approved dust masks.

• Hearing protection.

Always maintain your balance.

Do not stretch yourself over running machines.

8. Residual risks

The machine is built according to the latest tech-

nology and the recognized technical safety-re-

lated rules. Nevertheless, individual residual

risks can occur during operation.

• Danger of Injury to ngers and hands from the run-

ning tool if it is used incorrectly.

• Risk to health from dust. Wear personal protec-

tion equipment such as eye protection without fail.

• Injuries due to defective diamond cutting disc. The

diamond cutting disc must be checked regularly for

physical integrity.

• Risk of injury to ngers and hands during cut-

ting disc replacement. Wear appropriate working

gloves.

• Risk of injury during machine activation from sud-

den start of cutting disc.

• Risk from power while using improper electric con-

necting cables.

• Risk to health from running cutting disc due to long

hair and loose clothing. Wear personal protection

equipment like hair net and tight-tting working

clothes.

• Even after taking all the necessary precautions,

not apparent residual risks cannot be ruled out

completely.

• Residual risks can be minimized if the „safety in-

structions“ and the „proper use“, as well as operat-

ing instructions manual are observed jointly.

9. Before start-up

Replace cracked diamond cutting discs.

• Get to know your machine. Familiarize yourself

with its use and its restrictions, but also with the

specic potential risks.

• Check the machine carefully for damages to en-

sure that it is able to achieve the intended output.

In case of doubt, please replace the concerned

component.

• Ensure that the switch is on Off, before inserting

the power plug into the mains socket.

• Ensure that the machine is cleaned and lubricat-

ed properly.

• Before start-up, check the machine for damaged

parts and nd out whether these parts are work-

ing properly and performing their dened function.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach HSM3500 in the language / languages: English, German, French, Spanish as an attachment in your email.

The manual is 6.7 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach HSM3500 Manual

Product: