Manual Scheppach HSM3500 (page 27 of 92) (English, German, French, Spanish)

781910

Zoom out

Zoom in

1/92

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

GB | 27

• Use only cutting wheels which are designed for a

minimum speed of 3000 min-1.

• Selecting the cutting wheel Select the diamond

cutting wheel to suit the material you want to cut.

• Fitting the cutting wheel: Before you install the cut-

ting wheel, check the spindle, the spindle nut and

the anges for damage, wear or a loose t. Re-

place damaged or worn parts without delay.

• Direction of rotation of the cutting wheel: Check

the direction arrow on the cutting wheel; the arrow

must point in the same direction as the direction in

which the motor shaft rotates.

• Cutting wheel spindle: Make sure that the diameter

of the hole in the cutting wheel is the same as the di-

ameter of the cutting wheel spindle on the machine.

• Cutting wheel guard: Only use the tile cutting ma-

chine with a properly tted and adjusted cutting

wheel guard.

• Cutting wheel speed: Do not exceed the safe oper-

ating speed of the cutting wheel.

• Sanding/grinding with the cutting wheel Do not try

to use the cutting wheel for sanding or grinding

jobs, e.g. to sand/grind the edge of a cut tile. Al-

so, do not use the machine for radius cuts or round

cuts. This tile cutting machine is suitable only for

household use.

• Cutting wheel stop time: After the machine has

been switched off, the cutting wheel needs 40 sec-

onds to come to a standstill. Wait until the cutting

wheel has stopped completely, pull the power plug

out of the socket outlet, and only then touch the

cutting wheel if necessary.

• Avoid all contact with the rotating cutting wheel

when the machine is in operation.

• The electric tool must never be used without the

PRCD plug supplied with it.

• Keep water away from electrical parts of the tool

and from persons in the work area!

• If the power plug or the power cable are damaged

they must be replaced either by the manufacturer

or by a service company authorized by the manu-

facturer.

• To comply with the requirements imposed by the

safety regulations, all technical modications

which change the equipment‘s characteristics (e.g.

speed) must be left strictly to the manufacturer.

• Keep this safety information in a safe place.

Special safety instructions for stone cutting ma-

chines

• Place the stone cutting machine on a level work

surface with stable footing before using it. Ensure

that there is sufcient room for freedom of move-

ment.

• In order to avoid a dust hazard, the machine may

only be used in the wet area. This is also mandato-

ry because the diamond cutting wheel is only suit-

able for wet cutting.

19. Check damaged parts

Before further use of the tool, a guard or other

part that is damaged should be carefully checked

to determine that it will operate properly and per-

form its intended function. Check for alignment of

moving parts, binding of moving parts, breakage

of parts, mounting, and any other conditions that

may affect its operation. A guard or other part

that is damaged should be properly repaired or

replaced by an authorized service center unless

otherwise indicated elsewhere in this instructions

manual. Have defective switches replaced by

an authorized service center. Do not use tool if

switch does not turn it on and off .

20. Warning

The use of any other accessory or attachment

other than recommended it this operating instruc-

tion or the catalog may present a risk of personal

injury.

21. Have your tool repared by an expert

This electric appliance is in accordance with the

relevant safety rules repairing of electric appli-

ances may be carried out only by experts oth-

erwise it may cause considerable danger for the

user.

22. Connect the dust extraction device

Wherever there are facilities for tting a dust ex-

traction system, make sure it is connected and

used.

Warning! This electric tool generates an electro-

magnetic eld during operation. This eld can impair

active or passive medical implants under certain

conditions. In order to prevent the risk of serious or

deadly injuries, we recommend that persons with

medical implants consult with their physician and the

manufacturer of the medical implant prior to operat-

ing the electric tool.

Special safety information

Caution! This tile cutting machine is designed for wet

cutting only. The machine may be operated only with

a non-segmented diamond cutting wheel.

• Wet hands: Never touch the electrical components

of the machine (e.g. switches) with wet hands.

• Plug-in connections: All plug-in connections must

be located in a dry place and must not lie on the

oor.

• Cooling the cutting wheel: Make sure that the cut-

ting wheel is cooled with water during the complete

cutting process.

• Dry cutting: Never carry out dry cuts with cutting

wheels designed for wet cutting.

• Dust protection: Always wear a protective dust

mask when cutting tiles.

• Diamond cutting wheels: Do not feed the tile into

the machine any faster than the cutting wheel can

cut.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach HSM3500 in the language / languages: English, German, French, Spanish as an attachment in your email.

The manual is 6.7 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach HSM3500 Manual

Product: