644558
17
Zoom out
Zoom in
Previous page
1/103
Next page
health risk. During operation, the admis-
sible noise level is exceeded. Thus, wear
personal protective equipment such as ear
protection at all times.
Defective saw blades can cause injuries.
Check the saw blade regularly and before
each use for intactness.
Operating the power tool causes electrical
hazards, never use improper electrical
access lines.
When using optional accessories, always
read and observe the enclosed operating
instructions carefully.
Despite all of the precautionary measures
taken, there could be non-apparent, residual
dangers.
By observing the safety information, the
information in the chapter „Intended use“
and the operating instructions in general,
you can reduce the residual risks.
Installation
Prepare the workplace where you intend
to place the electrical power tool. Provide
enough space to ensure safe and trouble-
free operation. The power tool is designed
for working in enclosed rooms and has to be
installed on level and rm ground.
Equipment Fig. 1
1 Saw table
2 Protective cover
3 Push stick
4 Saw blade
5 Splitting wedge
6 Stage centre
7 Longitudinal stop
8 Main connection
9 Frame
10 On/off switch
11 Height adjustment handle
12 Angle adjusting wheel
13 Scale for the angle adjustment
14 Locking handle
15 Star grip for the longitudinal stop
16 Rip fence
17 Overload switch
18 Table extension
19 Fold-out support feet
20 Stop bar
Assembly
Assembly and modication work may
only be performed when the mains plug is
pulled out.
For packing-related reasons, the electrical
power tool must be mounted by the operator.
Open the box and remove the packaging and
Styrofoam parts.
Remove the enclosed individual parts.
Remove the power tool from the box and
place it on the oor. Ensure to use a piece of
cardboard as a base in order to protect the
oor.
Note: The electrical power tool is heavy; thus
two people should lift the device out of its
packaging.
ASSEMBLY PROTECTIVE COVER Fig. 2
In order to mount the protective cover (2),
place it above the splitting wedge (5), so
that the screw ts into the slit of the splitting
wedge. Then, push the protective cover into
the bottom of the opening. Screw the wing
nut tight, so that the protective cover sits on
the table top (1), but lifts itself, when the work
piece is pushed towards the saw blade. Make
sure to move the protective cover back to its
idle position after you have nished cutting.
Note: The protective cover (2) has to be in
working position at all times in order to avoid
contact with the saw blade.
ASSEMBLY LONGITUDINAL STOP Fig. 3
Use the star grip screws (27) to mount the
clamping claws (26) to the stop tube (28) on
both sides. Use the clamping claws to insert
the longitudinal stop (7) laterally into the table
top (1).
Use the star grip screws to tighten the longitu-
dinal stop on both sides.
ASSEMBLY RIP FENCE Fig. 4
Insert the rip fence (13) into the groove on the
saw bench (1). Loosen the lobe knob (24),
adjust to the desired number and tighten the
lobe knob again. You can use the stop bar (20)
of the rip fence (7) to improve the work piece
guidance by tightening the stop bar to the rip
fence using 2 groove screws and 2 star grip
screws.
Commissioning
Follow the safety instructions!
Important: Be sure to mount all protection
and safety devices and to connect the
power tool to the exhaust system before
commissioning the electric power tool. Also
make sure to lower the protective cover to the
work piece for any process of the power tool.
Before turning on the electric power tool,
all protection and safety devices have to be
installed properly.
Ensure that the saw blade can move freely.
Check wood that has been processed already
for foreign objects (nails, screws and so on).
Remove all foreign objects and connect the
power tool to a socket with a ground. Before
you turn on the main switch, ensure that the
saw blade is mounted properly and that the
movable parts are running smoothly. Warning:
If you have any doubts, let an expert assemble
the power tool. It is too dangerous to work on
the basis of assumptions.
ADJUSTING THE CUTTING HEIGHT Fig. 5
The saw blade has to be adjusted in such a
way that the top of the highest saw tooth is
slightly higher than the work piece.
The saw blade (4) can be adjusted to the
intended cutting height by rotating the height
adjustment handle (11. Rotating counter
clockwise enlarges the cutting height, rotating
clockwise reduces the cutting height.
ADJUSTING THE ANGLE OF THE SAW
BLADE Fig.6
Loosen the locking handle (14). You can
adjust the saw blade (4) to the intended
angle on the scale (13) by rotating the angle
adjusting wheel (12). Tighten the locking
handle (14) again.
CALIBRATING THE ANGLE OF THE SAW
BLADE. Fig.7
Attention! Pull out the main plug
The scale (13) can be calibrated during the
examination of the angular accuracy of the
saw. Adjust the saw blade at the very top;
make sure to have a right angle to the saw
blade. Adjust the angle adjusting wheel (11)
in a way that the saw blade is parallel to the
angle.
Adjust the pointer to an angle of 0°.
SWITCH ON AND OFF
Green button = On
Red button = Off
Operating instructions
OVERLOAD PROTECTION
This electrical power tool is provided with an overload protection. In case that the overload protection was initiated, proceed
GB
17
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach HS80 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach HS80 in the language / languages: English, German, Danish, French, Italian, Swedish, Finnish as an attachment in your email.

The manual is 8,45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Scheppach HS80

Scheppach HS80 User Manual - All languages - 288 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info