644558
19
Zoom out
Zoom in
Previous page
1/103
Next page
TABLE EXTENSION
When cutting wider work pieces, you should
use the table extension (18, Fig.1).
Loosen the knurled screws under the table
top.
Pull out the table extension
Fold out the support feet (19, Fig.1)
Re-tighten the knurled screws.
Electrical connection m
The installed electric motor is connected and
ready for operation. The connection complies
with the applicable VDE and DIN require-
ments.
The power supply provided by the customer
and the applied connection cable have to com-
ply with these requirements as well.
Important Information
The electric motor 230 V/50 Hz is suitable for
the operation mode S6 / 40%. On motor over-
load, the motor will turn off automatically. The
motor can be turned on after a cooling period
(of varying duration).
Defective electrical connection cables
Electrical connection cables are a likely sub-
ject to insulation damages.
Causes for that could be:
Pressure marks that occur when connection
cables are guided through windows or door
gaps.
Kinks caused by improper fastening or con-
trol of the connection cables.
Interfaces when overrunning the connection
cable.
Insulation damages when pulling out the
cable out of the wall socket.
Cracks caused by the ageing of the insula-
tion.
Such defective electrical connection cables
may not be used anymore and can be fatal
due to the possible insulation damages.
Check electrical connection cables for da-
mages regularly. When doing so, ensure that
the connection cable is not connected to the
power supply. Electrical connection cables
must comply with the applicable VDE and DIN
requirements. Use only connection cables
carrying the marking H 07 RN. It is required by
law that connection cables carry the label with
the type designation.
AC motor (alternating current motor)
• The power supply must be 230 Volt – 50 Hz.
Extension cables must have a cross-section
of 1,5 mm2 when shorter than 25 m and a mi-
nimum cross-section of 25 mm2 when longer
than 25 m.
The power supply is protected by 16 A (slow)
fuse.
Connections and repairs on the elec-
trical equipment may only be perfor-
med by qualied electricians.
Please submit the following details on request.
• Motor manufacturer
• Type of current of the motor
Details printed on the machine’s type plate.
Send in the complete drive unit incl. switch
when returning the motor.
Follow the safety instructions!
Cleansing, maintenance and repair
m
WARNING
Remove the plug from the wall socket when working on the electrical power tool itself (e.g. transportation, setup,
conversion, cleansing and maintenance works)!
CLEANSING
Let the electrical power tool cool down after
each usage.
Clean the power tool with a moist cloth and a
bit of soap after using it. Use a brush or scrub-
ber for the use in difcult accessible areas.
Note: Do not use aggressive cleansing agents
or solvents. These could damage the plastic
and metallic components of the electrical
power tool.
Clean the interior of your power tool such
as the gear segment and the pinion of the
slewing mechanism of all wood and splinter
residues regularly
Use an appropriate blunt tool to remove possi-
ble blockages on the suction strainer that were
caused by the sawdust.
WARNING
m Do not try to remove blockages with
your hand or ngers!
Remove especially persistent residue in inac-
cessible places using compressed air (max.
3 bar).
MAINTENANCE
Check the power tool and its accessories (e.g.
tool adaptor) for wear and damages before
and after each usage. If necessary replace
them with new ones according to the instruc-
tions in this manual. When doing so, please
respect the general technical requirements.
Check the saw blade regularly. Use only shar-
pened, crack-free, not deformed saw blades.
Use only tools that comply with the European
standard EN 847-1.
Replace a worn out stage blade immediately
with a new one of the same type.
Keep the table top free of resin at all times
CHANGING THE SAW BLADE FIG. 14, 15
Wear gloves when working with the saw
blade.
Loosen the 4 fastening screws (21) to ip the
saw blade cover (21) upwards.
Place the wring spanner (22) on the clamping
nut, while holding the sidewinder key (23)
against it.
Attention! Loosen the clamping nut in the
running direction of the saw blade.
Take off the saw blade ange and detach the
saw blade diagonally downwards.
Clean both saw blade anges carefully before
mounting a new saw blade.
The assembly of the saw blade is performed in
reverse order.
Attention! Pay attention to the running direc-
tion of the saw blade.
ADJUSTING THE SPLITTING WEDGE FIG.16, 17, 18
Loosen the wing nut to remove the saw blade
protection (2).
Remove 8 cross-head screws and remove the
stage centre (6).
Loosen the two cross-head screws.
Adjust the splitting wedge (5) in such a way
GB
19
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach HS80 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach HS80 in the language / languages: English, German, Danish, French, Italian, Swedish, Finnish as an attachment in your email.

The manual is 8,45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Scheppach HS80

Scheppach HS80 User Manual - All languages - 288 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info