Manual Scheppach HMS850 (page 25 of 148) (English, German, Danish, French, Italian, Polish)

759249

Zoom out

Zoom in

1/148

25GB

• Undo the clamp screws (A) by turning them

clockwise using the open-ended spanner (17)

supplied. Turn the knife block (23) so that the

latch (22) can be pulled out with the knife (21).

• Clean all the relevant parts and the knife slots in

the knife block (23).

• Fit the latch (22) with the new knife (21) and align

them with the side of the knife block.

• Place the blade adjustment block (15), as shown

in Figure 18, on the knife block. Make sure that

the knife (21) touches both sides of the blade

adjustment block (15).

• Tighten the clamp screws (A) using the openend-

ed spanner (17) supplied.

• Return the planing knife cover (12) to its original

position so that the knife (21) is covered.

m IMPORTANT!

Only use knives which are recommended by the

manufacturer for this equipment. If you use other

knives there is a risk of injuries due to lack of control.

Avoid over-tightening and the possibility of the

thread becoming detached. If the latch (22) or the

screws have worn out threads they must be immedi-

ately replaced.

10. Cleaning, maintenance and or-

dering of spare parts

General maintenance measures

Wipe chips and dust off the machine from time to

time using a cloth. In order to extend the service life

of the tool, oil the rotary parts once monthly.

Do not oil the motor.

When cleaning the plastic do not use corrosive

products.

m WARNING! Before cleaning~, adjustment~, main-

tenance~ or repair work, disconnect the power cord

from the main power supply!

10.1 Cleaning

• Keep all safety devices, air vents and the motor

housing free of dirt and dust as far as possible.

Wipe the equipment with a clean cloth or blow it

with compressed air at low pressure.

• We recommend that you clean the device immedi-

ately each time you have nished using it.

• Clean the equipment regularly with a moist cloth

and some soft soap. Do not use cleaning agents

or solvents; these could attack the plastic parts of

the equipment. Ensure that no water can seep into

the device. The ingress of water into an electric

tool increases the risk of an electric shock.

• The sawdust ejection and/or dust exhauster

should be cleaned at regular intervals.

• Never spray water on the machine!

10.2 Maintenance (Figure 1/15)

10.2.1 Machine

Lubricate the following parts periodically after

around 10 hours of service:

• Bearings for the feed/discharge rollers and anti-

kick claws (24)

• Bearings on the belt roller and pulley

• Grub screws to adjust the height of the thickness-

ing table (20)

Use only dry lubricant.

The feed table (13), planing table (14), thicknessing

table, feed/discharge rollers and anti-kick claws (24)

must be kept free of resin at all times. Soiled feed/

discharge rollers or anti-kick claws (24) must be

cleaned without delay. To prevent the motor over-

heating, the dust that accumulates in the ventilation

openings must be removed at regular intervals.

Improve the smooth running of the tables by apply-

ing lubricant at regular intervals.

10.2.2 Cutting tool

Resin must be cleaned off the knife (21), latch (22)

and knife block (23) at regular intervals. Clean these

components with an appropriate resin remover.

10.3 Ordering replacement parts:

Please quote the following data when ordering

replacement parts;

• Type of machine

• Article number of the machine

• Identication number of the machine

• Replacement part number of the part required

Repairs and works specied in these Instructions

may only be performed by qualied authorised staff.

Service information

Please note that the following parts of this product

are subject to normal or natural wear and that the

following parts are therefore also required for use as

consumables.

Wear parts:*

• motor drive belt

• carbon brushes

• planer blades

* Not necessarily included in the scope of delivery!

11. Storage

Store the equipment and accessories out of chil-

dren’s reach in a dark and dry place at above

freezing temperature. The ideal storage tempera-

ture is between 5 and 30 °C.

Store the electric tool in its original packaging.

Cover the electrical tool in order to protect it from

dust and moisture.

Store the operating manual with the electrical tool.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach HMS850 in the language / languages: English, German, Danish, French, Italian, Polish as an attachment in your email.

The manual is 6,85 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach HMS850 Manual

Product: