Manual Scheppach HMS850 (page 23 of 148) (English, German, Danish, French, Italian, Polish)

759249

Zoom out

Zoom in

1/148

23GB

Wear ear-muffs.

Wear ear-muff s.

The impact of noise can cause damage to hearing.

Keep the noise emissions and vibrations to a

minimum!

• Only use appliances which are in perfect working

order.

• Service and clean the appliance regularly.

• Adapt your working style to suit the appliance.

• Do not overload the appliance.

• Have the appliance serviced whenever necessary.

• Switch the appliance off when it is not in use.

7. Work preparation / operation

Before each use, check the following:

• Proper function of the on and off button, incl. the

emergency switch (if available).

• Locked disconnected protective equipment (D1,D2)

by gradual opening of every separating protective

equipment to be able to turn the machine off and

checking that the machine cannot be turned on

whenever the protective equipment is open

• Brake

by means of a function test to establish whether

the braking process takes place within the speci-

ed braking time and, if the machine is tted with

a mechanical brake, that the brake must be tested

each time the overload guard is tripped

• Anti-kick claws (24)

at least once per shift by a visual inspection to

establish that they are in good working order, for

example, that the contact surface has not been

damaged by impacts and that the anti-kick claws

(24) fall back without hindrance due to their own

weight;

• Planing blades

for signs of damage and to ensure they are posi-

tioned correctly.

The machine may only be used if all these condi-

tions are satised.

Use only well sharpened and maintained blades.

Use only blades that are designed for the machine.

Use pusher wood or sticks which are in perfect con-

dition for machining short workpieces.

Connect the machine to a dust and chip extractor.

Check that the stop is secure before starting the

machining work.

Ensure that you can maintain your balance at all

times. Stand to the side of the machine.

Whilst the machine is running keep your hands at

a safe distance from the cutting roller and from the

point at which the chips are discharged.

Do not start the planing work until the cutting roller

has reached the required speed.

Also ensure that the workpiece does not contain any

cables, wires, cords or the like. Do not machine any

wood which has lots of knots or knot holes.

Secure long workpieces to prevent them tipping over

at the end of the planing process. Use roller stands,

for example, or similar devices for this purpose.

Removing sawdust and chippings from the machine

when running is strictly prohibited.

Switch off the machine immediately it is jams. Pull

out the mains plug and remove the jammed work-

piece.

Set the smallest cutting size after use to prevent the

risk of injury.

m CAUTION!

The machine must be secured to the oor / coun-

tertop using suitable screws / screw clamps since

otherwise there is a risk that it will tip over. (Fig.19)

■ Before you connect the equipment to the mains

supply make sure that the data on the rating plate

are identical to the mains data.

■m WARNING! Before cleaning~, adjustment~,

maintenance~ or repair work, disconnect the

power cord from the main power supply!

■Check at regular intervals that the knife (21) and

latch (22) are rmly attached in the knife block

(23). (Figure 17)

■The knives (21) must not project more than a

maximum of 1.1 mm out of the knife block (23).

(Figure 18)

■Make sure that the anti-kick claws (24) work cor-

rectly. (Figure 15)

■ Always wear eye protection.

■Never cut concavities, tenons or shapes.

■ All covers and safety devices have to be properly

tted before the machine is switched on.

■It must be possible for the planing knife to run

freely.

8. Assembly

8.1 Parallel stop (Figure 4/5)

• Place the mount (25) against the feed table (13).

• Make sure that the holes in the mount (25) line up

with the female threads in the feed table (13).

• Secure the mount (25) to the feed table (13) using

the two Allen screws supplied.

8.2 Planing knife cover (Figure 1-3)

• Place the holder for the planing knife cover (8) on

the left-hand side of the planing table (14) so that

the pin and grub screw engage in the two holes.

• Secure the planing knife cover (12) using the lock-

ing knob (33) supplied

8.3 Rubber feet (Figure 1-2)

Secure the four rubber feet (11) to the bottom side

of the equipment using the Allen screws (37) and

washers (36) supplied.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach HMS850 in the language / languages: English, German, Danish, French, Italian, Polish as an attachment in your email.

The manual is 6,85 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach HMS850 Manual

Product: