781460
23
Zoom out
Zoom in
Previous page
1/124
Next page
www.scheppach.com / service@scheppach.com / +(49)-08223-4002-99 / +(49)-08223-4002-58
GB | 23
Caution: The device starts running immediately
at the set speed.
Speed adjustment (Fig. 1)
The correct speed must be set to suit the workpiece
to be processed.
Electronic speed control:
Use the electronic speed control to steplessly set the
speed:
Set the speed with the help of the speed control (3).
Important information for operation
We recommend that you refer to specialised litera-
ture on wood-turning techniques.
Look out for knots and shrinkage shakes when
selecting the wood for your turning work. Only
use wood which is free of cracks and large knots
(where there are small knots, take appropriate care
with the pressure applied with the turning tool).
Always check that the shaped item is securely held
by checking it by hand. Warning! Pull out the power
plug!
Use only an original turning tool which is sharp.
Do not stand in the ight path of the workpiece
when turning wooden disks.
Please cut large and imbalanced shaped items to
size as best as possible using a bandsaw or fret-
saw. If the shaped items are very imbalanced they
will pose a risk to your health and to the service life
of the machine.
Always start with the lowest possible speed for
new workpieces being turned and increase it with
increasing massiveness of the workpiece being
turned.
Do not use wooden disks with contraction cracks,
since they pose a high risk of bursting under the
impact of centrifugal forces.
Do not exceed the maximum workpiece sizes.
In case of tools which get blocked: Pull out the pow-
er plug rst before starting troubleshooting.
To do your turning work, position yourself at the
machine so that you can guide the cutting tools ef-
fectively on the tool support.
Only use cutting tools, which are recommended for
wood turning works.
9. Transport
1. Turn the power tool off before it is transported and
disconnect it from the power supply.
2. Always carry the electric tool with at least one oth-
er person. Carry the power tool to the machine
bed (12).
3. Protect the power tool against knocks, jolts and
strong vibrations, e. g. when it is transported in
motor vehicles.
4. Secure the power tool against tilting and sliding.
Caution: Before starting the machine test the set-
up by rotating the workpiece by hand to ensure
that there is enough clearance all the way around
and that it does not come into contact with the
tool support (6).
Using the face plate: (Fig. 3)
To use the faceplate:
The faceplate (15) offers solid and secure support
for a variety of turned objects such as platters,
bowls, pots and round pieces.
Installing the faceplate:
1. Loosen the headstock drive centre (4) and re-
move from the spindle.
2. Thread the faceplate (15) onto the headstock
spindle and tighten by hand and the wrench.
Securing workpiece on the faceplate:
Workpieces that cannot be worked using the head-
stock drive centre (4), instead must be mounted on a
faceplate (15) or a backing piece, such as a chuck or
block of wood.
1. Rough cut the workpiece as close as possible to
the nal shape before mounting onto the face-
plate (15).
2. Firmly attach the faceplate (15) to the workpiece.
Depending on the workpiece, this can be done
with wood screws (not supplied) driven directly
into the workpiece. Where the intended cutting di-
mensions do not allow for screws, a backing piece
might be required. A backing piece can be made
from a piece of scrap wood cube with two at and
parallel opposite faces. Identify and mark the cen-
tre of the backing piece.
It may be necessary to bond the carrier part
(wooden block) with the workpiece and attach it
to the carrier part, before fastening it to the face
plate (15) using screws (not included in the scope
of delivery). In this case, clamp the backing piece
to the workpiece and wait for the glue to dry ac-
cording to the glue manufacturers recommenda-
tion. Where the use of screws into the workpieceis
not permissible, the workpiece can be glued onto
a backing piece with a piece of paper placed in
between the joint. This allows for later separation
without damage caused to the workpiece. Use
only non-tapered head wood screws. Do not use
tapered head wood screws.
Caution: Pay attention to the wood turning chis-
el so that it does not interfere with the holding
screws at the nished dimensions of the work-
piece.
Switching on and off (Fig. 1)
Press the On switch (2/„I“)to start the machine.
Press the Off switch (2/0) to stop the machine.
23


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach DM600VARIO at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach DM600VARIO in the language / languages: English, German, French, Italian, Polish as an attachment in your email.

The manual is 7.36 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info