781462

Scheppach DECO-XLS Manual

34
Zoom out
Zoom in
Previous page
1/112
Next page
www.scheppach.com
34 | GB
12.2.2 Carbon brushes
In case of excessive sparking, have the carbon brush-
es checked only by a qualied electrician.
IMPORTANT
The carbon brushes should not be replaced by anyone
but a qualied electrician.
12.2.3 Mains cable
If the mains cable is pulled out, cut, or damaged in
some other form, then it should be replaced immedi-
ately.
12.2.4 Replacing the ne-wire fuse (g. 16)
If the ne-wire fuse (36) is defective, it must be re-
placed with a ne-wire fuse of the same type.
WARNING
Do not bypass the ne-wire fuse (36)! Do not use fus-
es of any other type! This can lead to damage to the
device.
12.3 Service information
Please note that the following parts of this product are
subject to normal or natural wear and that the following
parts are therefore also required for use as consum-
ables.
Wear parts*: Carbon brushes, saw blade, table inlay
* Not necessarily included in the scope of delivery!
Spare parts and accessories can be obtained from our
service centre. To do this, scan the QR code on the
cover page.
12.4 Ordering replacement parts
The following information must be provided on all or-
ders for spare parts:
• Device type
• Device article number
13. Storage
Store the equipment and accessories out of children’s
reach in a dark and dry place at above freezing temper-
ature. The ideal storage temperature is between 5 and
30 °C. Store the electric tool in its original packaging.
11. Transport
• Transport the electric tool by lifting it on the recesses
provided for this on the frame and the engine cover.
• Never use the protective devices for handling or
transport.
• Make sure that the exposed part of the saw blade
is covered during transport, e. g. by the protective
device.
12. Cleaning, maintenance, storage
and ordering of spare parts
WARNING
Always switch the machine o󰀨 and remove the mains
plug prior to all maintenance and cleaning work.
12.1 Cleaning
Keep all safety devices, air vents and the motor hous-
ing free of dirt and dust as far as possible. We recom-
mend that you clean the equipment immediately after
you use it.
12.1.1 Exterior cleaning
• Clean the equipment regularly with a damp cloth and
some soft soap.
• Do not use cleaning agents or solvents; these may
be aggressive to the plastic parts in the equipment.
• Ensure that no water can get into the interior of the
equipment.
12.1.2 Interior cleaning (g. 15)
1. Open the storage box (9).
2. Remove the screw (35).
3. Loosen the screw (34).
4. Remove the cover (8).
5. Blow out the device interior with low-pressure
compressed air.
6. Attach the cover again (8).
7. Fasten the screw (34).
8. Insert the screw (35) again and tighten it.
9. Close the storage box (9).
12.2 Servicing
12.2.1 Bearings (g. 1/pos. 10)
Lubricate the bearing points (10) of the deection roll-
ers after approx. 25-30 operating hours at the latest
using high-quality machine grease.
… 34 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach DECO-XLS at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach DECO-XLS in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 5 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info