Manual Scheppach DECO-XLS (page 32 of 112) (English, German, Dutch, French, Italian, Portuguese, Spanish)

781462

Zoom out

Zoom in

1/112

www.scheppach.com

32 | GB

• When cutting thicker wood, special attention must

be paid not to bend or twist the saw blade.

• Handling the saw blade properly increases its ser-

vice life.

9.2 On/o󰀨 switch (16)

• Switching on: Press the “I” button.

• Switching o󰀨: Press the “0” button.

ATTENTION

The machine is equipped with a safety switch against

reactivation if the voltage drops.

If the scroll saw is switched on and the power supply

in the mains is interrupted, the scroll saw remains

switched o󰀨, even if the power supply is re-established.

Press the “I” button to switch it on.

9.3 Work lamp operation (g. 4)

1. Switch the machine on as described in 9.2.

2. The work lamp (20) may not be switched on/and o󰀨

with the work lamp on/o󰀨 switch (21).

9.4 Stroke rate controller (g. 2)

The stroke rate controller (18) allows you to set the

stroke rate according to the material to be cut. In case

of soft material, we recommend high stroke rates, while

strokes rates should be kept low for hard material. Turn

the stroke rate controller (18) clockwise to increase the

stroke rate. Turning anti-clockwise lowers the stroke

rate.

9.5 Operating modes (g. 1, 2)

The scroll saw is able to be operated manually or via

the foot pedal.

9.5.1 Manual controls

1. Ensure that the machine is switched on.

2. Set the operating mode selection switch (17) to the

“M” position to operate the saw manually.

8.5 Installing the depressor (g. 6, 7)

NOTE:

Before assembling the depressor (24), the saw blade

pre-installed at the factory (22) must be removed (see

8.1.3).

1. Remove the saw blade (22) as described in 8.1.3.

2. Remove the depressor (24) from the saw blade

guard (5) by loosening the screw (25) completely

(see g. 6).

3. Insert the holder (4) into the opening (see g. 7).

4. Fasten the holder (4) with the knurled screw (3).

5. Install the depressor (24). Insert the screw (25) into

the holder (4) and fasten it.

6. Insert the saw blade (22) again as described in

8.1.3.

7. Ensure that the depressor (24) does not contact

the saw blade (22).

The depressor (24) must always be adjusted accord-

ing to the workpiece height. However, the workpiece

should not be clamped, but should rather be able to

move freely.

The depressor (24) is used to lock the workpiece so

that it cannot swing upwards, which would destroy the

saw blade (22).

8.6 Chip extraction (g. 13)

ATTENTION: Only operate the device with an extrac-

tion system.

Connect a suitable chip extraction system (not included

in the scope of delivery) to the suction connection (15)

(see g. 13, sample gure).

ATTENTION: Check and clean the suction channels at

regular intervals.

9. Operation

9.1 General information

• The saw does not cut wood automatically. Rather,

the operator must push and guide the wood toward

the moving saw blade.

• The teeth only cut the wood on the downstroke.

• The wood must be slowly pushed and guided toward

the saw blade, since the teeth of the blade are very

small.

• Those who want to use the saw must go through the

process of learning how to do so. During this time, a

few blades will invariably break.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach DECO-XLS in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 5 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach DECO-XLS Manual

Product: