781462
31
Zoom out
Zoom in
Previous page
1/112
Next page
www.scheppach.com GB | 31
6. Put the table insert (26) back.
NOTE
The left side features a storage box (9), which enables
you to stow replacement saw blades and the hexagon
wrench.
8.2 Checking the saw blade tension
WARNING
Check the blade tension regularly and after insert-
ing a saw blade.
Tension the saw blade after assembly by pressing
down on the tension lever (11).
If the blade tension is too low or too high, proceed as
follows:
Fold the tension lever (11) upwards.
Turn the tension lever (11) clockwise to increase the
tension and anti-clockwise to reduce it.
Press the tension lever down again to engage the
setting.
If the tension is correct, the saw blade should produce
a light tone when it is plucked, like a string.
8.3 Calibrating the angle scale (g. 12, 12.1)
IMPORTANT
Check the adjustment of the angular scale before you
start working with the unit.
1. Loosen the locknut of the adjustment screw (37).
2. To set the saw table, use a 90° bracket (31, not in
the scope of delivery). Place this against the saw
table and the saw blade (g. 12).
3. Adjust the adjustment screw (37) until the angle
between the saw blade (22) and the saw table (6)
is 90°.
4. Tighten the locknut of the adjustment screw (37)
again.
5. Loosen the screw (32) and turn the pointer (33) to
the 0° marking.
6. Make a test cut. Check the angle on the workpiece
with a protractor. If necessary, readjust the pointer
(33).
8.4 Installing the blow-o󰀨 device (g. 8)
1. Ensure that the saw blade guard (5) folded down.
2. Screw the blow-o󰀨 device (1) clockwise onto the
holder (2) as described in g. 8.
4. Then loosen the upper saw blade clamping lever
(28), followed by the lower saw blade clamping le-
ver (29) using the Allen key (23).
8.1.2 Inserting the saw blade without pins
(optional)
The teeth of the saw blade must always point down-
wards.
1. First, secure the saw blade (22) in the lower saw
blade mounting (30). To secure the saw blade (22),
tighten the lower saw blade clamping screw (29)
using the Allen key (23).
2. Press the support (12) down lightly. Fasten the oth-
er end of the saw blade (22) in the top saw blade
holder (27) (see g. 9).
3. Fix the saw blade (22) with the upper blade clamp-
ing screw (28) (see g. 10).
4. Tighten the saw blade (22) with the clamping lever
(11), by pressing it down again. Check the tension
of the saw blade (22). If the tension is insu󰀩cient,
it can be increased by turning the lever clockwise.
First release the clamping lever (11).
5. Put the table insert (26) back.
8.1.3 Removing the saw blade with pins
1. To remove the saw blade (22), lift the table insert
(26) upwards.
2. First, release the tension by ipping the tension
lever (11) upwards. Continue reducing the tension
by turning clockwise as required.
3. Press the support (12) down lightly (see g. 9).
4. Pull the saw blade from the upper and lower saw
blade mounting (27/30).
8.1.4 Inserting the saw blade with pins
The teeth of the saw blade must always point down-
wards.
1. Insert one end of the saw blade (22) through the
drilled hole in the table. Insert the pins of the saw
blade (22) into the corresponding recesses of the
top and bottom saw blade holder (27/30).
2. First insert the saw blade (22), in the lower blade
holder (30).
3. Press the support (12) down lightly (see g. 9).
4. Check the position of the saw blade pins in the saw
blade mountings (27/30).
5. Tighten the saw blade (22) with the clamping lever
(11), by pressing it down again. Check the tension
of the saw blade (22). If the tension is insu󰀩cient,
it can be increased by turning the lever (11) clock-
wise.
31


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach DECO-XLS at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach DECO-XLS in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 5 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info