781462
30
Zoom out
Zoom in
Previous page
1/112
Next page
www.scheppach.com
30 | GB
7.3 Installing the fretsaw on a workbench
Required for installing:
Included in the scope of delivery:
M8 hexagonal bolt (4x)
M8 hexagonal nut (4x)
Washer Ø 9 mm (8x)
The length of the screws to be used varies, depending
on the thickness of the table top.
WARNING
Danger of injury! Disconnect the mains plug on the
scroll saw before all assembly work.
1. The length of the screws to be used varies, de-
pending on the thickness of the table top.
2. Mark the drill holes (see g. 5.2).
3. Drill 4 holes with a diameter of 8 mm into the work
table.
4. Screw the scroll saw onto the workbench with the
hexagonal bolt (E) through the assembly points
(g. 3 pos. 19) in the following sequence (g. 5.1):
A Fretsaw
B Work table
C Washer
D Hexagonal nut
5. Tighten the hexagonal nut (D) rst.
8. Assembly
WARNING
Danger of injury! Disconnect the mains plug on the
scroll saw before all assembly work.
8.1 Fitting / Replacing the saw blade (g. 1, 8-11)
IMPORTANT
To avoid injuries attributed to inadvertent startup: Be-
fore removing or replacing the saw blade, always press
0“ and remove the mains plug from the socket.
8.1.1 Removing the saw blade without pins (option-
al)
1. To remove the saw blade (22) , lift the table insert
(26) upwards.
2. First, release the tension by ipping the tension
lever (11) upwards. Continue reducing the tension
by turning clockwise as required.
3. Press the support (12) down lightly (see g. 9).
Adopt your way of working to the equipment.
Do not overload the equipment.
Have the equipment checked if necessary.
Switch o󰀨 the equipment when not in use.
Suitable saw blades
All industry-standard saw blades with a minimum
length of 127 mm with and without a pin may be used.
7. Before starting the machine
7.1 Unpacking
Open the packaging and remove the device care-
fully.
Remove the packaging material as well as the pack-
aging and transport bracing (if available).
Check that the delivery is complete.
Check the device and accessory parts for transport
damage.
If possible, store the packaging until the warranty
period has expired.
ATTENTION
The device and packaging materials are not toys!
Children must not be allowed to play with plastic
bags, lm and small parts! There is a risk of swal-
lowing and su󰀨ocation!
7.2 General notes
All covers and safety devices have to be properly
tted before the equipment is switched on.
It must be possible for the blade to run freely.
When working with wood that has been processed
before, watch out for foreign bodies such as nails
or screws, etc.
Before you actuate the On/O󰀨 switch, make sure
that the saw blade is correctly tted and that the
equipment’s moving parts run smoothly.
Check that the voltage on the rating plate is the
same as your supply voltage before you connect the
equipment to the power supply.
Only ever connect the equipment to a properly in-
stalled shock-proof socket which is protected by a
10A fuse as a minimum.
30


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach DECO-XLS at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach DECO-XLS in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 5 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info