Manual Scheppach CAG115-20ProS (page 24 of 92) (English, German, French, Polish)

781689

Zoom out

Zoom in

1/92

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

24 | GB

5. Before using the tool on an actual workpiece, let

it run for a while. Watch for vibration or wobbling

that could indicate poor installation or a poorly

balanced wheel.

6. Use the specied surface of the wheel to perform

the grinding.

7. Do not leave the tool running. Operate the tool

only when hand-held.

8. Do not touch the workpiece immediately after op-

eration; it may be extremely hot and could burn

your skin.

9. Observe the instructions of the manufacturer for

correct mounting and use of wheels. Handle and

store wheels with care.

10. Do not use separate reducing bushings or adap-

tors to adapt large hole abrasive wheels.

11. Use only anges specied for this tool.

12. For tools intended to be tted with threaded hole

wheel, ensure that the thread in the wheel is long

enough to accept the spindle length.

13. Check that the workpiece is properly supported.

14. Pay attention that the wheel continues to rotate

after the tool is switched off.

15. If working place is extremely hot and humid, or

badly polluted by conductive dust, use a shortcir-

cuit breaker (30 mA) to assure operator safety.

16. Do not use the tool on any materials containing

asbestos.

17. When use cut-off wheel, always work with the

dust collecting wheel guard required by domestic

regulation.

18. Cutting wheels must not be subjected to any lat-

eral pressure.

m WARNING

This electric tool generates an electromagnetic

eld during operation. This eld can impair ac-

tive or passive medical implants under certain

conditions. In order to prevent the risk of serious

or deadly injuries, we recommend that persons

with medical implants consult with their physi-

cian and the manufacturer of the medical implant

prior to operating the electric tool.

Information on the rechargeable battery

Please observe the operating manual for the re-

chargeable batteries.

Information on the charging unit and charging

process

Please observe the operating manual for the charg-

ing unit.

Additional safety warnings specic for abrasive

cutting-off operations:

a) Do not “jam” the cut-off wheel or apply ex-

cessive pressure. Do not attempt to make an

excessive depth of cut. Overstressing the wheel

increases the loading and susceptibility to twisting

or binding of the wheel in the cut and the possibil-

ity of kickback or wheel breakage.

b) Do not position your body in line with and be-

hind the rotating wheel. When the wheel, at the

point of operation, is moving away from your body,

the possible kickback may propel the spinning

wheel and the power tool directly at you.

c) When wheel is binding or when interrupting a

cut for any reason, switch off the power tool

and hold the power tool motionless until the

wheel comes to a complete stop. Never at-

tempt to remove the cut-off wheel from the cut

while the wheel is in motion otherwise kick-

back may occur. Investigate and take corrective

action to eliminate the cause of wheel binding.

d) Do not restart the cutting operation in the

workpiece. Let the wheel reach full speed and

carefully re-enter the cut. The wheel may bind,

walk up or kickback if the power tool is restarted

in the workpiece.

e) Support panels or any oversized workpiece to

minimize the risk of wheel pinching and kick-

back. Large workpieces tend to sag under

their own weight. Supports must be placed un-

der the workpiece near the line of cut and near the

edge of the workpiece on both sides of the wheel.

f) Use extra caution when making a “pocket

cut” into existing walls or other blind areas.

The protruding wheel may cut gas or water pipes,

electrical wiring or objects that can cause kick-

back.

g) Do not make curved cuts. Overstressing the

wheel increases the loading and susceptibility to

twisting and binding of the wheel in the cut and

the possibility of kickback or wheel breakage,

which can lead to serious injuries.

6. Additional Safety Warnings

1. When using depressed centre grinding wheels,

be sure to use only berglass-reinforced wheels.

2. Never use Stone Cup type wheels with this grind-

er. This grinder is not designed for these types of

wheels and the use of such a product may result

in serious personal injury.

3. Be careful not to damage the spindle, the ange

(especially the installing surface) or the lock nut.

Damage to these parts could result in wheel

breakage.

4. Make sure the wheel is not contacting the work-

piece before the switch is turned on.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach CAG115-20ProS in the language / languages: English, German, French, Polish as an attachment in your email.

The manual is 4.11 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach CAG115-20ProS Manual

Product: