Manual Scheppach CAG115-20ProS (page 23 of 92) (English, German, French, Polish)

781689

Zoom out

Zoom in

1/92

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

GB | 23

d) Use special care when working corners, sharp

edges, etc. Avoid bouncing and snagging the

insertion tool. Corners, sharp edges or bounc-

ing have a tendency to snag the rotating insertion

tool and cause loss of control or kickback.

e) Do not attach a saw chain blade for wood-cut-

ting, a segmented diamond saw blade with a

segment distance of more than 10 mm or a

toothed saw blade. Such insertion tools create

frequent kickback and loss of control.

Safety warnings specic for grinding and

abrasive cutting-off operations:

a) Use only wheel types that are recommended

for your power tool and the specic guard de-

signed for the selected wheel. Wheels for which

the power tool was not designed cannot be ade-

quately shielded and are unsafe.

b) Depressed centre grinding wheels must be

mounted in such a way that their grinding sur-

face does not protrude above the plane of the

guard edge. An improperly mounted wheel that

protrudes above the plane of the guard edge can-

not be adequately shielded.

c) The guard must be securely attached to the

power tool and positioned for maximum safe-

ty, so the least amount of wheel is exposed to-

wards the operator. The guard helps to protect

the operator from broken wheel fragments, acci-

dental contact with wheel and sparks that could

ignite clothing.

d) Wheels must be used only for recommended

applications. For example: Do not grind with

the side of a cut-off wheel. Abrasive cut-off

wheels are intended for peripheral grinding. Side

forces applied to these wheels may cause them

to shatter.

e) Always use undamaged wheel anges that

are of correct size and shape for your selected

wheel. Proper wheel anges support the wheel

thus reducing the possibility of wheel breakage.

Flanges for cut-off wheels may be different from

grinding wheel anges.

f) Do not use worn down wheels from larger

power tools. Wheels intended for larger pow-

er tool are not suitable for the higher speed of a

smaller tool and may burst.

g) When using wheels for a dual purpose, always

choose the appropriate guard for the applica-

tion being carried out. Failure to use the proper

guard may result in ineffective shielding and in

serious injuries.

l) Never lay the power tool down until the inser-

tion tool has come to a complete stop. The ro-

tating insertion tool may grab the surface and pull

the power tool out of your control.

m) Do not run the power tool while carrying it at

your side. Accidental contact with the rotating in-

sertion tool could snag your clothing, pulling the

insertion tool into your body.

n) Regularly clean the power tool’s air vents. The

motor’s fan will draw the dust inside the housing

and excessive accumulation of powdered metal

may cause electrical hazards.

o) Do not operate the power tool near ammable

materials. Sparks could ignite these materials.

p) Do not use insertion tools that require liquid

coolants. Using water or other liquid coolants

may result in electric shock.

Kickback and related safety warnings

Kickback is a sudden reaction to a pinched or

snagged rotating insertion tool, such as a grinding

wheel, grinding pad, brush wire, etc. Pinching or

snagging causes the rotating insertion tool to stop

abruptly which in turn causes the uncontrolled power

tool to be forced in the direction opposite of the inser-

tion tool’s rotation at the point of the binding.

For example, if a grinding wheel is snagged or

pinched by the workpiece, the edge of the grinding

wheel which is entering into the workpiece may be-

come caught causing the grinding wheel to break off

or kick back. The grinding wheel then either jumps

toward or away from the operator, depending on

the direction of the wheels’ movement at the point

of pinching. Grinding wheels may also break under

these conditions.

Kickback is the result of power tool misuse and/or in-

correct operating procedures or conditions. It can be

avoided by taking proper precautions as given below.

a) Maintain a rm grip on the power tool and po-

sition your body and arm to allow you to resist

kickback forces. Always use auxiliary handle,

if provided, for maximum control over kick-

back or torque reaction during start-up. The

operator can control torque reactions or kickback

forces, if proper precautions are taken.

b) Never place your hand near the rotating inser-

tion tool. Insertion tool may kickback over your

hand.

c) Do not position your body in the area where

power tool will move if kickback occurs. Kick-

back will propel the tool in the direction opposite

to the wheel’s movement at the point of snagging.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach CAG115-20ProS in the language / languages: English, German, French, Polish as an attachment in your email.

The manual is 4.11 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach CAG115-20ProS Manual

Product: