Manual Scheppach CAG115-20ProS (page 22 of 92) (English, German, French, Polish)

781689

Zoom out

Zoom in

1/92

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

22 | GB

e) The outside diameter and the thickness of the

insertion tool must correspond to the dimen-

sions of the power tool. Incorrectly measured

insertion tools cannot be adequately shielded or

controlled.

f) Threaded mounting of insertion tools must

match the grinder spindle thread. For inser-

tion tools mounted by anges, the arbour

hole of the insertion tool must t the locating

diameter of the ange. Insertion tools, which do

not t exactly on the grinding spindle of the power

tool, rotate unevenly, vibrate violently and may re-

sult in loss of control.

g) Do not use a damaged insertion tool. Before

each use, inspect the insertion tool such as

abrasive wheels for chips and cracks, back-

ing pad for cracks, tear or excess wear, wire

brush for loose or cracked wires. If power tool

or insertion tool is dropped, inspect for dam-

age or install an undamaged insertion tool.

After inspecting and installing the tool, posi-

tion yourself and bystanders away from the

plane of the rotating insertion tool and run the

power tool at maximum speed for one minute.

Damaged insertion tools usually break during this

test time.

h) Wear personal protective equipment. Depend-

ing on application, use full face protection,

eye protection or safety goggles. As appro-

priate, wear dust mask, hearing protection,

protective gloves and/or workshop apron ca-

pable of stopping small abrasive or workpiece

fragments. The eye protection must be capable

of stopping ying debris generated by various op-

erations. The dust mask or respirator must be ca-

pable of ltrating particles generated by your oper-

ation. Prolonged exposure to high intensity noise

may cause hearing loss.

i) Keep bystanders a safe distance away from

your work area. Anyone entering the work area

must wear personal protective equipment.

Fragments of the workpiece or of broken insertion

tools may y away and cause injury even beyond

the immediate work area.

j) Hold the power tool by insulated gripping

surfaces only, when performing an operation

where the cutting tool may contact hidden

wiring. Contact with a “live” wire will also make

exposed metal parts of the power tool “live” and

could give the operator an electric shock.

k) Position the cord clear of the rotating inser-

tion tool. If you lose control, the cord may be cut

or snagged and your hand or arm may be pulled

into the rotating insertion tool.

d) Store idle power tools out of the reach of chil-

dren and do not allow persons unfamiliar with

the power tool or these instructions to oper-

ate the power tool. Power tools are dangerous in

the hands of untrained users.

e) Maintain power tools and accessories. Check

for misalignment or binding of moving parts,

breakage of parts and any other condition

that may affect the power tool’s operation. If

damaged, have the power tool repaired before

use. Many accidents are caused by poorly main-

tained power tools.

f) Keep cutting tools clean and sharp. Properly

maintained cutting tools with sharp cutting edges

are less likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits

etc. in accordance with these instructions,

taking into account the working conditions

and the work to be performed. Use of the power

tool for operations different from those intended

could result in a hazardous situation.

h) Keep handles and grasping surfaces dry,

clean and free from oil and grease. Slippery

handles and grasping surfaces do not allow for

safe handling and control of the power tool in un-

expected situations.

5) Service

a) Have your power tool serviced by a qualied

repair person using only identical replace-

ment parts. This will ensure that the safety of the

power tool is maintained.

Safety warnings common for grinding, sanding,

wire brushing, or abrasive cutting-off operations:

a) This power tool is intended to function as a

grinder or cut-off tool. Read all safety warn-

ings, instructions, illustrations and data pro-

vided with this power tool. If you do not observe

the following instructions, an electric shock, re

and/or serious injuries may occur.

b) Operations such as sanding, wire brushing

polishing or hole cutting are not recommend-

ed to be performed with this power tool. Oper-

ations for which the power tool was not designed

may create a hazard and cause personal injury.

c) Do not use insertion tools which are not spe-

cically designed and recommended by the

tool manufacturer. Just because the accessory

can be attached to your power tool, it does not

assure safe operation.

d) The permitted speed of the insertion tool

must be at least equal to the maximum speed

indicated on the power tool. An insertion tool

which rotates faster than permitted may shatter

and y off.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach CAG115-20ProS in the language / languages: English, German, French, Polish as an attachment in your email.

The manual is 4.11 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach CAG115-20ProS Manual

Product: