782056
31
Zoom out
Zoom in
Previous page
1/128
Next page
31
Installation et réglage des barres de pression, Fig. 24
• Lesbarresdepression(5)sontconstruitesdefaçonà
retenir la pièce à usiner sur place et à servir de disposi-
tif anti-retour.
glage du calibre de découpe en biais
• Lecalibrededécoupeenbiais (8)glisse horizontale-
ment le long de la table pour effectuer des découpes de
rectification et des coupes de biais.
• Pourréglerlecalibrede découpe en biaissur l’angle
souhaité,desserrerleboutondeverrouillage(7)duca-
libre et tourner sur l’angle souhaité compris.
Resserrer le bouton de verrouillage du calibre de -
coupeenbiais(7).
Fig. 24
• Toujourseffectuerunecoupedetestsurunepiècede
déchet pour s’assurer que les réglages sont corrects.
Mise en service et hors service, Fig. 2527
S’assurer que toutes les clés et outils de réglage ont été
enlevés de la table de fraisage, que les réglages sont au
complet et que les systèmes de sécurité sont montés.
L’interrupteurMARCHE/ARRÊTestcommandéparl’inter-
médiaire d’un disjoncteur sous un couvercle rouge, qui est
rabattu sur l’interrupteur MARCHE/ARRêT. Pour mettre
en marche, appuyer d’abord sur le bouton de verrouillage
(Fig.25),ouvrirlecouvercleetmaintenirouvert(Fig.26),
ensuitepresserleboutondemarche(Fig.27).Lamachine
démarre. Laisser retomber le couvercle sur l’interrupteur.
Ne pas verrouiller le couvercle.
Pour arrêter, appuyer simplement sur le couvercle rouge
quis’enclenchealors.Celaappuiesurleboutond’ArrÊt
situé en dessous et coupe l’alimentation électrique. Pour
la remise en marche, le couvercle doit être déverrouil
et soulevé. Ce produit dispose d’un commutateur électro-
magnétique comme protection supplémentaire. Quand le
courant est interrompu, le commutateur passe de nouveau
dans la position d’arrêt. Pour redémarrer le moteur il faut
denouveauappuyersurleboutonvertMARCHE.
Installing and adjusting the pressure limits, Fig. 24
• Thepressurelimits(5)aredesignedsothatthework
piece is held on the spot and setback is avoided.
Adjust the Cross-cutting jig
• Slidehorizontalalongthetablethecrosscuttingjig(8)
in order to implement clean up error and mitre cuts.
• Inordertostopthejigatthedesiredangle,loosenthe
lockingknob(7)ofthecrosscuttingjigandturnthisto
the desired angle.
Tightenthelockingknobofthejig(7)again.
Fig. 24
• Alwaysmakeasamplecutinapieceofwastematerial
in order to guarantee that the attitudes are correct.
Switching on and off, Fig. 25–27
Make sure that all keys and adjusting tools are well away
from the spare desk that the attitudes are installed in full
and all safety covers are kept.
The Circuit breaker is switched over a safety switch that
has red cover and is folded over Circuit breaker. For
switchingon,pressrstthelockingknob(Fig.25),fold
thecoverupwardandkeeprm(Fig.26),thenpressthe
switchingon button(Fig. 27).Themachinestartsnow.
Let the cover on the switches fall.
To stop the machine simply push the red cover; it pushes
the underneath lying OFF-button and thus stops the cir-
cuit.
This machine uses an electromagnetic switch for optimal
security. Whenever the current is interrupted the machine
stops immediately. To restart the machine the green but-
ton must be pushed again
31


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach BS 52 Woodster at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach BS 52 Woodster in the language / languages: English, German, Danish, French, Italian, Swedish, Finnish as an attachment in your email.

The manual is 6.29 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info