782113
21
Zoom out
Zoom in
Previous page
1/48
Next page
21
33A
33
35
Z
GB
S
GB
D
34
A
4.6 Travail de pièces courtes et étroites (33-33A)
Utiliser une pièce de maintien qui garantit une prise sûre.
Exécuter la pièce de maintien de telle manière qu’elle permette une
pression forte de la pièce contre les guides et la table machine
4.6 Working with short and narrow pieces (33-33A)
Use a clamping piece to ensure a firm hold of the workpiece.
Set the maintaining piece in place so that it holds securely the work-
piece against the guides and the machine table.
4.6 Fräsen von kurzen Werkstücken mit kleinem Querschnitt (33-33A)
Werkstück nur mit Zuführlade bearbeiten.
Das Haltestück so ausführen, daß hierdurch ein starker Druck des
Werkstückes auf die Führungen und den Maschinentisch gewährleistet
wird.
D
GB
F
4.8 Réglage individuel de la garniture (35)
Par action sur la poignée (S) et blocage par le levier (Z).
Ce réglage permet un guidage de la pièce après usinage.
4.8 Tiefeneinstellung der Holzgarnitur (35)
Durch Betätigen des Knopfes (S) und Blockieren mit dem
Handgriff (Z).
Dies erlaubt eine eiwandfreie Führung des Werkstücks nach
der Bearbeitung.
D
F
4.8 Individual adjustment of the wooden fence (35)
By operating the handle (S) and locking with the lever (Z).
With this adjustment, the piece can be supported after machining.
4.7 Chantournage externe (34)
Régler la toupie. Utiliser de préférence un outil qui travaille par en
dessous.
Confectionner un contre-guide en bois limitant le dépassement de
l’outil.
Repérer sur ce guide le point (A) de pénétration maximum de l’outil.
Guider la pièce à chantourner en veillant qu’elle tangente toujours
le repère (A).
F
4.7 Exterior chamfering (34)
Adjust the spindle tool. Use tool for bottom machining.
Fix an additional wooden fence to limit the cutting depth of the tool.
Mark on the fence the point where the tool reaches maximum depth
(A) of cut.
Feed the workpiece ensuring the timber is always cutting at the
marked «max. depth of cut point» (A).
4.7 Fräsen von Außenbogen (34)
Die Fräse einstellen. Vorzugsweise, Werkzeuge für bearbeitung
von unten benutzen.
Vorsetzbrett anfertigen das zur Werkzeugtiefeneinstellung dient.
Auf dem Vorsetzbrett die Maximale Schnitttiefe markieren (A)
Das Werkstück so bearbeiten daß es immer an der Markierungs-
stelle (A) anliegt.
21


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach Bestcombi 5.0 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach Bestcombi 5.0 in the language / languages: English, German, French as an attachment in your email.

The manual is 6.33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info