629722
64
Zoom out
Zoom in
Previous page
1/93
Next page
62 VERSA IP SATEL
1. Enter a number from the 0 to 50 range to define the rules of device presence control, and
then press .
2. Use the and keys to define how the acoustic signaling will work (
disabled; 1, 2 or 3 – type of acoustic signaling), and then press .
3. Use the and keys to define the maximum duration of signaling, and then
press .
4. Define whether the optical signaling is to be enabled ( – no, – yes), and then press
.
ASW-100 E / ASW-100 F controller
1. Enter a number from the 0 to 50 range to define the rules of device presence control, and
then press .
2. Use the and keys to define mode of operation of the button (“inactive” – the
electric circuit is controlled remotely only; “interim control” – the electric circuit can be
controlled remotely or manually; “combined control” – the electric circuit can be controlled
remotely or manually, but the remote control can be manually overridden), and then press
.
9.4.4 Specific character of the operation of wireless devices
This chapter describes the peculiar character of the operation of individual groups of wireless
devices, which affects the method of programming the zones and outputs to which the
wireless devices are assigned.
ABAX wireless detectors
The wireless detectors send information on violations, tampers and low-battery status. The
information on violations and tampers is sent to the zones to which the detectors are
assigned. You can program these zones as:
NC, NO or EOL – the zone will inform about detector violation,
2EOL/NC or 2EOL/NO – the zone will inform about detector violation and tamper.
The mode of operation of wireless detectors depends on the status of partition to which the
zone with wireless detector belongs:
partition disarmed – the detector operates in passive mode. It is a battery saving mode, in
which communication with the controller takes place mainly during time intervals
determined by the RESPONSE PERIOD parameter. At that time, information on violations and
battery status is sent. Only detector tampers are sent immediately.
partition armed – the detector operates in active mode. The detector sends immediately all
information to the controller.
Because switching the detectors over from the passive into active mode and conversely
takes place during the response time, it is performed with some delay in relation to
arming/disarming. The maximum delay – depending on the selected response frequency –
can be 12, 24 or 36 seconds.
The AMD-103 detector and the wireless detectors assigned to 24-h zones, i.e. always armed,
are in active mode at all times. Also other wireless detectors can always operate in active
mode, if the A
LWAYS ACTIVE option is enabled for them (see: “Parameters and options of
ABAX system wireless devices” p. 55).
According to the EN50131-3 standard all ABAX sy
stem Hold-Up devices must be
always in active mode.
64


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel Versa IP at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel Versa IP in the language / languages: English as an attachment in your email.

The manual is 1,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel Versa IP

Satel Versa IP Quick start guide - English - 11 pages

Satel Versa IP User Manual - English - 32 pages

Satel Versa IP Installation Guide - English - 36 pages

Satel Versa IP User Manual - English - 43 pages

Satel Versa IP Quick start guide - German - 11 pages

Satel Versa IP Additional guide - German - 97 pages

Satel Versa IP User Manual - German - 45 pages

Satel Versa IP Installation Guide - German - 38 pages

Satel Versa IP Quick start guide - Dutch - 2 pages

Satel Versa IP User Manual - Dutch - 45 pages

Satel Versa IP Quick start guide - Dutch - 12 pages

Satel Versa IP Additional guide - Dutch - 93 pages

Satel Versa IP User Manual - Dutch - 45 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info