699578
14
Zoom out
Zoom in
Previous page
1/40
Next page
12 Programming CA-6
Functions programming zone parameters
FS24 - programming zone sensitivity
Each zone of the CA-6 can have an individual reaction time. Violations lasting shorter than
the programmed reaction time are disregarded by the control panel. Programming the
zones sensitivity in keypad is performed in a different way, than programming the other
parameters. The programming includes values from 1 to 255 which corresponds to the
times from 16 ms to 4080 ms according to the formula:
REACTION TIME = PROGRAMMED VALUE x
16 ms
By default, all the zones have the same reaction time (480 ms). In most cases, no change
of the time setting is required.
The function is intended for advanced installers. It allows the zone sensitivity to be
selected when special detectors are used (for example, mechanical glass break detectors,
or low hysteresis detectors, not fitted with monovibrator at the output).
Note: The minimum keypad zones sensitivity is 64ms (4 x 16 ms). The actual
sensitivity values of these zones can amount to n x 64ms (n=1,2,3,...). This
results from the way the keypad is operated by the control panel – the
zones status is read out at 64ms intervals.
During programming, the AB, AB LEDs indicate which zone the parameter refers to. The
zone number is displayed in binary format (for zone no. 1 – the lower B LED is blinking, for
zone no. 2 – the lower A LED, for zone no. 3 – both of them, etc.).
After setting a value for the given zone, press the [#] key to proceed to programming the
reaction time of the next zone. After the last parameter is entered and confirmed, the
control panel exits the function. The introduced changes will only be displayed after the
function is reentered.
The programming can be interrupted by using the [
*
] key.
EXAMPLE:
changing the reaction time of zones 1, 3 and 6 to 800 ms, zone 8 to 100 ms, the other
zones unchanged
800 ms/16 ms = 50 (enter this value for zones 1,3 and 6)
100 ms /16 ms = 6.25 (enter 6 for zone 8, it will ensure the reaction time = 96 ms)
[12345] [#] - enter the service mode
[2][4] [#] - call the function
[5][0] [#] - reaction time for the first zone (AB, AB LEDs = 0001)
[#] - confirm the second zone time (AB, AB LEDs = 0010)
[5][0] [#] - reaction time for the third zone (AB, AB LEDs = 0011)
[#] - confirm the fourth zone time (AB, AB LEDs = 0100)
[#] - confirm the fifth zone time (AB, AB LEDs = 0101)
[5][0] [#] - reaction time for the sixth zone (AB, AB LEDs = 0110)
[#] - confirm the seventh zone time (AB, AB LEDs = 0111)
[6] [#] - reaction time for the eighth zone (AB, AB LEDs = 1000)
the control panel automatically exits the function
Note: The parameter is entered in decimal and indicated in binary format.
A new value can be checked only after reentering function. It is displayed in binary format
on LEDs from 1 to 8.
The LEDs which are off mean 0. The value of the LEDs which are on corresponds with the
table below:
LED number 1 2 3 4 5 6 7 8
Bit weight 128 64 32 16 8 4 2 1
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel CA-6 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel CA-6 in the language / languages: English as an attachment in your email.

The manual is 0,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel CA-6

Satel CA-6 Quick start guide - English - 8 pages

Satel CA-6 Installation Guide - English - 36 pages

Satel CA-6 Additional guide - German - 19 pages

Satel CA-6 User Manual - German - 19 pages

Satel CA-6 Installation Guide - German - 80 pages

Satel CA-6 User Manual - German - 18 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info