699578
12
Zoom out
Zoom in
Previous page
1/40
Next page
10 Programming CA-6
EXAMPLE:
programming the counters: the 1
st
- 2 violations, the 2
nd
- 5 violations, the 3
rd
- without
changes
[12345] [#] - enter the service mode
[7] [#] - call the required function
[0][2] [#] - program the first counter (the lower B LED is blinking)
[0][5] [#] - program the second counter (the lower LED A is blinking)
[
*
] - exit the function - programming of the third counter is omitted
In case of programming three counters, the function is automatically exited after the third
counter
Functions programming assignment
FS8 - programming A partition zones (BIT)
FS9 - programming B partition zones (BIT)
The functions FS8 and FS9 are used to divide the alarm system into partitions.
It is possible to assign any zone to the partitions. Independent sirens and messaging
telephone numbers can be assigned to the partitions, and separate access codes can be
programmed – thus creating two independent alarm systems.
Optionally, the so-called interior partition can also be created (if one partition is to be fully
contained in the other).
When both partitions are armed, it is possible to disarm the interior partition by
using its code. The other zones, which belong to the primary partition, will remain
armed.
Note: If the armed mode is activated by means of the primary partition code, the interior
partition zones will be automatically armed as well, but their status as a partition
status will not be signaled by the control panel – the
[
ARMED
] LED, which
corresponds to the interior partition, is "off".
A zone can be assigned to both partitions at the same time. The common zone will only be
armed, when both partitions are armed (if the partitions do not contain one another, i.e. the
partition is not the interior one).
Zones can be assigned to the partition by pressing the keys 1 to 8, which is shown by
lighting of the LED which indicates the respective zone. Use the [#] key to confirm the
selection and exit the function. Use the [
*
] key to interrupt the programming.
FS16 - programming auto bypassed zones in A partition (BIT)
The AUTO BYPASS function applies to the zones which are automatically bypassed after
arming with the 7 authority level code (partial arming), assigned to the A partition. The
same zones are bypassed after silent arming of the A partition.
The control panel permits also programming another set of automatically bypassed zones:
bypassed when no exit from the partition (EXIT-BYPASS zones - with service functions
FS127, FS128).
The programming is similar to the programming of FS8 function. After the corresponding
diodes are turned on the [#] key should be pressed.
FS17 - programming bypassed zones in B partition (BIT)
The function refers to the automatically bypassed zones in B partition. The programming
as in FS16.
FS20 - programming keypad and partition options (BIT)
Some of the user functions and the keypad beeps are optional. The FS20 function defines
which of them are to be performed.
Two sets of options are programmed, each of them need to be confirmed with the [#] key.
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel CA-6 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel CA-6 in the language / languages: English as an attachment in your email.

The manual is 0,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel CA-6

Satel CA-6 Quick start guide - English - 8 pages

Satel CA-6 Installation Guide - English - 36 pages

Satel CA-6 Additional guide - German - 19 pages

Satel CA-6 User Manual - German - 19 pages

Satel CA-6 Installation Guide - German - 80 pages

Satel CA-6 User Manual - German - 18 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info