699578
11
Zoom out
Zoom in
Previous page
1/40
Next page
CA-6 SATEL 9
THIRD SET the lower A and B diodes are blinking
No LED Option
ON
downloading unavailable if any partition is armed
2
OFF
downloading always available
ON
alarm if zones are violated after the exit delay elapses
3
OFF
control panel does not alarm if zones in partition are violated after the exit delay
elapses
ON
OUT4 and OUT5 outputs work in „UA” format
7
OFF
OUT4 and OUT5 outputs work in PC16OUT format
Note: The options: 1,4,5,6 and 8 from the third set of options are irrelevant in the CA-6.
FS6 - programming the global times (DEC)
The settings refer to the entry delay, exit delay and alarm time. The times are valid for the
entries and exits to which no individual times are assigned. The exit delay time is
common for all partitions. In case of the entry delay time it is possible to program an
individual delay for each zone and In case of the alarm time it is possible to program
a separate time for each output. The alarm time programmed in this function refers also to
the keypad alarm signaling.
Note: The alarm time set with the function FS6 defines also the zone alarms blocking
time - when the alarm is on, the subsequent zone violations will not trigger
consecutive alarms until the blocking time elapsed.
Programming the times is carried out in the following order:
- entry delay (from 00 to 99 seconds ) - the lower B diode is blinking,
- exit delay (from 00 to 99 seconds) - the lower A diode is blinking,
- alarm time (from 00 to 99 seconds) - the A and B diodes are blinking.
EXAMPLE:
programming the times: entry delay=30s, exit delay=60s, alarm=90s
[12345] [#] - enter the service mode
[6] [#] - call the required function
[3][0] [#] - enter the entry delay time (two digits) – the lower B LED is blinking
[6][0] [#] - enter the exit delay time (two digits) – the lower A LED is blinking
[9][0] [#] - enter the alarm time – the A and B LEDs are blinking - after acknowledging the last
settings, the control panel automatically exits the function
FS7 - programming the counting zone counters (DEC)
The control panel is equipped with three independent violation counters which can be
associated with any zones. Violation of these zones triggers an alarm after the
programmed number of violations is exceeded. All the violations must occur within
a specific period of time. Each counter can sum up violations of one or several zones
defined as the counting zones (e.g. the counter 1 can count violations of zone 2, the
counter 2 - violations of zones 4, 5, 6). The alarm will be generated by the zone which has
been violated as the last one.
Three counter values are programmed, from 01 to 07, in the following order: counter 1,
counter 2, counter 3. If no counting zones are provided in the panel, the programmed
values are irrelevant.
If "00" has been programmed, the counting zone will operate as the instant one.
Count times of the counters are programmed in FS123.
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel CA-6 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel CA-6 in the language / languages: English as an attachment in your email.

The manual is 0,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel CA-6

Satel CA-6 Quick start guide - English - 8 pages

Satel CA-6 Installation Guide - English - 36 pages

Satel CA-6 Additional guide - German - 19 pages

Satel CA-6 User Manual - German - 19 pages

Satel CA-6 Installation Guide - German - 80 pages

Satel CA-6 User Manual - German - 18 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info