699578
6
Zoom out
Zoom in
Previous page
1/40
Next page
General
The CA-6 control panel is characterized by a high flexibility of firmware, which enables their
functionality to be customized as per individual requirements of the protected premises.
Additionally, some extra functions can be assigned to the panel (for example, control of
lighting, locks, cameras).
The control panel can be configured from the keypad (locally) or by the computer with
a suitable firmware (locally via RS-232 port or remotely via modem). Programming with the
keypad is possible after starting the service mode. When programming from the keypad,
you should pay attention to information shown by means of the LED indicators and audible
signals.
Service mode [SERVICE CODE][#] or [SERVICE CODE][
*
]
The service mode can be started from the keypad in any disarmed and non-alarming
partition. In order to start the service mode, enter the service code (by default=[1][2][3][4][5])
and confirm it with the key [#] or [
*
]. The service mode is indicated by alternate blinking of the
[
POWER
] and the
[
PHONE
] LED and a short beep generated every 3 seconds (in the
CA-6 KLED-S keypad blinks LED designed ). No keypad tamper contact or address is
checked in the service mode. The service mode is on until deactivated by the service function
(FS0).
Programming the control panel service functions from keypad
The panel programming is based on three types of functions: bit (BIT), decimal (DEC) and
hexadecimal (HEX). The bit functions are used to program two-state parameters: YES and
NO (e.g. the functions of zone assignment to partition, options). The decimal functions are
used for programming a few digits data (for example, the test transmission time – 4 digits).
The hexadecimal functions are used to program hexadecimal data (e.g., monitoring codes).
During programming, if the functions have a several options (e.g., FS5, FS27), the number of
options set or the number of zone is shown on the
[
ALARM
AB] and
[
ARMED
AB] LEDs.
Calling a separate service function is indicated by lighting of the
[
TROUBLE
] LED.
BIT functions
During programming with a bit function, the LEDs 1 to 8 show the current setting of particular
parameters (diode on – YES, off – NO). Pressing the keys [1] to [8] changes the state of the
corresponding diode. The state of 8 parameters is confirmed with the [#] key. If the
programming function includes more parameters, the control panel will signal with two short
beeps acceptance of the first eight parameters and the LEDs 1 to 8 will display the state of
the next group of eight. The control panel shows on the
[
ALARM
AB]
and
[
ARMED
AB]
LEDs the set of options being currently programmed. When all the parameters have been
programmed, the control panel will signal exiting the function with four short beeps and a long
one.
The [
*
] key makes it possible to quit the function at any time without saving the changes in
currently displayed data.
DEC functions
During programming the LEDs 1-4 show the first digit (binary), LEDs 5-8 - the second digit,
while the LEDs AB, AB display the counter of digit pairs (binary). The programming consists
in entering a two-digit number and confirming it with the [#] key. The control panel will confirm
operation with two short beeps. When all the parameters have been programmed, the control
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel CA-6 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel CA-6 in the language / languages: English as an attachment in your email.

The manual is 0,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel CA-6

Satel CA-6 Quick start guide - English - 8 pages

Satel CA-6 Installation Guide - English - 36 pages

Satel CA-6 Additional guide - German - 19 pages

Satel CA-6 User Manual - German - 19 pages

Satel CA-6 Installation Guide - German - 80 pages

Satel CA-6 User Manual - German - 18 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info