699578
26
Zoom out
Zoom in
Previous page
1/36
Next page
24 SATEL Installer Manual
control panel reports the alarm more times than the preprogrammed number of
rounds the control panel recognizes answering the call on the basis of a callback signal
if the user lifts the handset too quickly (during the first ring), the control panel may
disregard the message and call again.
Reporting to telephone monitoring station
The monitoring station operator should provide the installer with the data necessary for the
monitoring software. These are:
monitoring station telephone numbers,
transmission format or a list of available formats,
alarm system identifier (facility number),
list of event codes.
In order to start monitoring, the following function should be programmed:
FS43 monitoring station telephone number if there are two numbers or two stations,
the second number should be programmed in FS44.
FS45, FS46 station transmission formats in case of a multi-format station, select
format which is as fast as possible (e.g. Ademco Express or Radionics 2300 with parity).
FS47 monitoring options.
FS48 to FS54 monitoring stations identifiers, an identifier should have 3 or 4 non-zero
characters (characters from 1 to F”, “0” no character), some stations use identifiers
composed from digits from 0 to 9 – then character “Ais to be programmed instead of digit
0” (e.g. “A1A2” instead of “0102”.
FS60 to FS65 & FS69 to FS70, FS81, FS82, FS126 event codes according to the list
from the monitoring station operator, the codes can be one-digit (the other character
being 0) or two-digit as required by the station, the codes with inappropriate length may
block communication with the station.
if reporting with event sorting to both stations has been selected in the options, events
assignment should be programmed in the functions FS67, FS68, FS73, FS74, FS77,
FS78, FS83, FS84.
FS5 – activate the “Monitoring” option if the above functions are programmed.
Note: In order to make monitoring possible when the control panel is in the downloading
mode, it is necessary to terminate communication by using the „Quit communication”
command in the „Communication” menu of the DLOAD10 program.
Typical problems with starting the monitoring:
Control panel takes no attempts to call – not all of the above mentioned functions have
been programmed – the control panel will not call the monitoring station if the programmed
data do not allow sending a correct transmission to the station because of e.g. missing
telephone number, identifier being shorter than 3 non-zero characters, missing event code,
etc. The control panel does not make any call attempts also when it is in the computer
downloading mode;
Problems with dialing no dial tone or a non-standard dial tone from the telephone
exchange find out the cause of missing signal or disable the dial tone test option in FS5
if the signal is non-standard;
Control panel sends no codes when connected to the station wrongly selected
format or low quality of telephone connection (the panel does not “understand” the station
dial tone);
26


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel CA-6 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel CA-6 in the language / languages: English as an attachment in your email.

The manual is 0,56 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel CA-6

Satel CA-6 Additional guide - English - 40 pages

Satel CA-6 Quick start guide - English - 8 pages

Satel CA-6 Additional guide - German - 19 pages

Satel CA-6 User Manual - German - 19 pages

Satel CA-6 Installation Guide - German - 80 pages

Satel CA-6 User Manual - German - 18 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info