699578
24
Zoom out
Zoom in
Previous page
1/36
Next page
22 SATEL Installer Manual
Entering service mode "from pins"
If the panel does not „see” the keypad when the power is on, and does not respond to the
keystrokes (access code entry), or keeps on alarming, it is necessary to carry out the
procedure of hardware access to the service mode. This allows to program keypad
address before the normal operating mode is restored. In the other case, the control panel
will start alarming right after the power-up because it has detected the keypad tampering.
This procedure is also required when the keypad address is changed – it is necessary to
program the address first (see: FS111 or FS124). Otherwise, the control panel may start
alarming just after power-up because a keypad tamper has been detected.
To start the service mode by means of jumpers follow the procedure below:
1. Disconnect in turn the AC supply and the battery.
2. Check the keypad address jumpers and tamper contacts for correct settings.
3. Place the jumper on RESET (J13) pins located on the control panel board.
4. Connect in turn the battery and the AC supply.
5. After a minute remove the jumper from RESET (J13) pins the control panel should
automatically enter the service mode. This will be signaled by the keypads with four short
and one long beeps.
6. Call the service function FS124. The function automatically reads the keypad address and
prepares the control panel for work in a new configuration. You can also restore the factory
default settings (FS107), restart the user passwords (FS110), and/or reset the event log
(FS108).
Note: Shorting the pins and power-up alone will restore no parameters! These
operations will call up the service mode, thus making it possible to program any
parameters required.
Having completed the procedure, exit the service mode using the function FS0 and activate
the service mode again this time from the keypad by entering the default access code
[1][2][3][4][5] confirmed with the [#] key.
If the control panel has re-entered the service mode, it means that its functioning is correct
and that you can proceed with further installation of the system (connection of sensors, sirens
or establishing communication with a computer, if necessary) and programming of all
required parameters.
If the described procedure is unsuccessful, the option of hardware access to the service
mode must have been disabled in the control panel by software means (see: FS131).
If this is the case, it is necessary to carry out another procedure which would enable the
control panel and restore the default settings:
1. Disconnect in turn the AC supply and the.
2. Set a jumper on RESET (J13) pins.
3. Connect in turn the battery and the AC supply.
4. Wait for a 60 seconds and then remove the jumper.
5. Enter from keypad the code: [1][2][3][4][5] (the code should be entered within 15 seconds)
and confirm by pressing the [#] or [
*
] key – the control panel enters the service mode.
ACTIVATING SELECTED FUNCTIONS
Performance of some functions of the control panel requires that a few or more parameters
should be programmed. This section contains detailed information on how to program such
functions as: guard control, telephone messaging, monitoring and downloading.
24


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel CA-6 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel CA-6 in the language / languages: English as an attachment in your email.

The manual is 0,56 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel CA-6

Satel CA-6 Additional guide - English - 40 pages

Satel CA-6 Quick start guide - English - 8 pages

Satel CA-6 Additional guide - German - 19 pages

Satel CA-6 User Manual - German - 19 pages

Satel CA-6 Installation Guide - German - 80 pages

Satel CA-6 User Manual - German - 18 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info