699578
22
Zoom out
Zoom in
Previous page
1/36
Next page
20 SATEL Installer Manual
the battery "-". Connecting the common ground of the device to the battery "-"
will result in faulty operation of the charging current limiter, which will
eventually lead a quick discharge of the battery, or may even cause damage to
the control panel.
Connections of Telephone Line
If the control panel telephone communicator is used in the alarm system (for monitoring,
messaging or remote programming), it is necessary to connect telephone line to the control
panel. It should be led to a connector situated on the right side of the printed board. In order
to ensure proper messaging, the control panel must be directly connected to the line
(terminals designated as TIP and RING), and any other devices (telephone, telefax) after
the control panel (terminals designated as T-1 and R-1). Such a connection will make it
possible for the control panel to fully engage the line for the time of calling, which prevents
the messaging function from being blocked by lifting the handset. Additionally, the telephones
connected after the control panel do not signal the dialing by the control panel.
The telephone line must be a four-wire line so that the control panel can be connected
before the other devices (telephone, telefax, etc.).
Notes:
Do not send telephone signals and alarm system signals by one multicore cable. This may
result in damage to the system in case of a high-voltage punch-through from the telephone
line.
Telephone terminals of the panel should be connected to PSTN (analog) lines only.
Connecting the telephone circuit directly to digital network (e.g. ISDN) will cause damage
to the equipment.
The system installer should give the necessary information on the way of connection
control panel to telephone network to the user.
Connection of Voice Synthesizer
Where the function of alarm messaging with
voice announcements is used, a voice
synthesizer must be connected to the control
panel. The CA-6 interfaces with the SM-2
synthesizer produced by SATEL.
The synthesizer socket (designated as: SM-2
VOICE SYNTHESIZER) is located at the right
side of PCB, between telephone line
connector and low-current output sockets.
The SM-2 synthesizer should be directly
plugged into this connector. It is fitted with
minijacks for playback of the message and
monitoring of the telephone line.
Connection of power supply
The control panel is permanently connected to the mains supply source. Hence, before
making the connections it is necessary to familiarize with the electric system in the facility.
For powering the control panel choose the circuit which is always live. The power supply
circuit should be protected with a proper fuse.
common ground
low-frequency signal
triggering
teltphone line monitoring
+ power supply (12 V)
panel board
Fig. 13. Arrangement of signals on SM-2
voice synthesizer connectors.
22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel CA-6 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel CA-6 in the language / languages: English as an attachment in your email.

The manual is 0,56 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel CA-6

Satel CA-6 Additional guide - English - 40 pages

Satel CA-6 Quick start guide - English - 8 pages

Satel CA-6 Additional guide - German - 19 pages

Satel CA-6 User Manual - German - 19 pages

Satel CA-6 Installation Guide - German - 80 pages

Satel CA-6 User Manual - German - 18 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info