699578
23
Zoom out
Zoom in
Previous page
1/36
Next page
CA-6 SATEL 21
Before connecting the control panel to its power supply circuit, make sure that
the supply circuit is not alive.
Description of electric connections for CA-6 OBU housing.
1. Connect the 230 V alternating voltage leads to the transformer terminals marked
"AC 230V".
2. Connect the terminals of the transformer secondary winding to the "AC" (~18 V) terminals
on the control panel mainboard.
3. Connect the wire of the electric shock protection circuit to the terminal block installed next
to the transformer and marked with the ground symbol . This circuit should also be
connected to the control panel protective terminal.
Never connect the "neutral" wire of the 230 V AC mains supply to the ground
terminal. If there is no separate electric shock protection circuit in the facility,
leave this terminal unconnected.
Control panel power supply starting procedure.
1. Connect the backup power supply wires to corresponding battery terminals (red to battery
plus, black to battery minus). The control panel will not start after connecting the
battery alone (without mains power supply) but it will operate in case of 230 V AC failure
provided that it was started earlier.
2. Switch on the 230 V AC mains supply – the control panel start follows.
Connection of the power supplies in the prescribed order will permit correct functioning of the
power supply unit and the control panel electronic safety circuits, thus avoiding damage to
the security system elements caused by possible installation faults.
Note: Should it be necessary to completely disconnect the control panel power supply
(the mains and the battery), re-connection of the power supply is to be performed in
the above mentioned order (the battery first, then the 230 V alternating voltage).
As the control panel has no isolating switch to disconnect the mains supply, it
is important that the owner or the user of the security system be informed on
how the system is to be disconnected from the mains (e.g. by indicating the fuse
which protects the control panel supply circuit).
Starting the control panel
When all electrical connections are made and checked for correctness, you can proceed to
starting the system. It is recommended to begin the work with the control panel with no sirens
connected. Sirens can be connected after alarm system parameters programming is
completed.
If the control panel operates with a keypad, having a default address (1001 - jumpers on pins
„D” and „A”), then, after the power is switched on, the keypad will report readiness for work
with four short beeps followed by a long one.
Note: The control panel with default settings will not support a keypad if the default address
(1001) has been changed in that keypad.
If the
[ALARM] diode is blinking, cancel it by entering the MASTER code [1][2][3][4] and
pressing [#]. Then, enter the default service code [1][2][3][4][5] and confirm it with the [#] key.
The control panel will enter the service mode, the
[POWER] and
[PHONE] diodes
alternately blinking. At this moment, you can proceed to programming the control panel.
23


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel CA-6 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel CA-6 in the language / languages: English as an attachment in your email.

The manual is 0,56 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel CA-6

Satel CA-6 Additional guide - English - 40 pages

Satel CA-6 Quick start guide - English - 8 pages

Satel CA-6 Additional guide - German - 19 pages

Satel CA-6 User Manual - German - 19 pages

Satel CA-6 Installation Guide - German - 80 pages

Satel CA-6 User Manual - German - 18 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info