699578
27
Zoom out
Zoom in
Previous page
1/36
Next page
CA-6 SATEL 25
Station does not receive or acknowledge the codes sent by the panel – wrongly
selected format, inadequate identifier length (3 characters, while the station requires 4),
inadequate event code length (1 character, while the station requires 2) or low quality of
telephone connection.
Note: For the Ademco Express transmission format, the identifier „0000” is valid (sending
zeroes is possible), however it is not valid with the other formats (sending zeroes is
impossible).
A headset connected to the "telephone line monitoring" jack in the SM-2 synthesizer can be
helpful in analyzing the problems with communication to the monitoring station.
Connection with the station is established in the following way:
the station answers the call and sends the, so-called, handshake signal (one or a few in
sequence if the station supports several transmission formats),
the control panel recognizes the station handshake signal and if it matches the
programmed transmission format, the control panel answers by sending identifier and
event code in appropriate tones (once or twice, depending on the selected format) in the
headset connected to the line monitoring jack, these sounds are much louder than the
monitoring station signals,
if the station receives information, it will acknowledge it with the same signal as the
handshake,
the panel disconnects or sends next codes if there still are some other events to be
reported to the station.
The most common monitoring problems result from inaccurate information on the
transmission formats supported by the given station (e.g., ambiguous names of the formats),
errors in the data entered into the control panel, as well as poor quality of the telephone
connections. Often only by “monitoring” process of communication you are able to find the
cause of a problem.
Note: Some stations do not acknowledge reception of the event code if it has another format
(e.g., 4/1 instead of the required 4/2). If this is the case, the control panel will repeat its
attempts to establish communication, while telephones in the facility will be
disconnected the costs of such connections may be very high. For this reason, it is
recommended that all the programmed codes be very carefully checked. It is possible
to activate the options 7 and 8 in FS47, which makes the panel ignore the codes
unacknowledged in 16 consecutive retries. Problems of this type do not occur in
professional, multi-format monitoring stations (including the Satel STAM-1).
Downloading – communication with computer
Programming the control panel through RS TTL serial port
The programming is possible with the use of a special cable (see: p. 12). To run the
software, select a suitable COM port number in the DLOAD10 program (“Configuration”
window). Then, from the “Communication” menu, select the
“Local connection
with...”, and, subsequently, select the control panel type (e.g.
CA6v5 - RS-232(TTL)”).
Activate the service function FS112 in the control panel. Consistency is required between
the panel and the computer communication codes (FS2 and FS3) programmed in the
panel and included in the DLOAD10 program data.
Programming with the use of modem
Telephone communication with the computer requires a modem. The modem must meet
two essential conditions:
27


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel CA-6 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel CA-6 in the language / languages: English as an attachment in your email.

The manual is 0,56 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel CA-6

Satel CA-6 Additional guide - English - 40 pages

Satel CA-6 Quick start guide - English - 8 pages

Satel CA-6 Additional guide - German - 19 pages

Satel CA-6 User Manual - German - 19 pages

Satel CA-6 Installation Guide - German - 80 pages

Satel CA-6 User Manual - German - 18 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info