699578
11
Zoom out
Zoom in
Previous page
1/36
Next page
CA-6 SATEL 9
It is possible to signal the exit delay or entry delay time, trouble, violation of a CHIME option
zone, violation of a DAY/NIGHT and COUNTING zone, alarm. You can also disable the
signaling of key depression and confirmation of the function performed.
The basic information on the system state is provided by means of light emitting diodes. They
present the state of zones and partitions (armed, alarm), as well as information on the status
of power supply and telephone line, as well as on troubles found.
The following features are also provided:
setting the keypad backlight mode with the key 9: none, automatic, permanent.
In the CA-6 KLED keypad, the backlighting can be switched on/off by means of pins
located next to the terminal block on the keypad board.
visualization of the keypad audible signal – buzzer (CA-6 KLED-S).
The keypad has an address, which makes difficult replacement or connection of another
keypad, an individual tamper contact and two zones, which operate identically as the zones
of the control panel mainboard. The keypad zones can be assigned to any partition. The data
concerning address, tamper contact and zone status, are sent to the control panel together
with keypad data.
Provision is made for connecting several keypads in parallel (which does not increase the
number of control panel zones).
Monitoring
The CA-6 control panel can transmit information about the system (partition) status to one or
two monitoring stations. Communication with the monitoring stations takes place irrespective
of the voice messaging and the messaging to paging systems. It has a priority and is realized
before the voice messaging. In case problems occur with getting connected to the station, the
control panel will suspend dialing the station number for 60 seconds and, if the message is
also to be transmitted by the dialer, it will make the line available to the dialer.
There are a few ways of transmitting information to the monitoring stations:
Reporting to one station.
Reporting to Station 1, and if unavailable to Station 2 (e.g., when the station has
two telephone numbers). If this is the case, all events are reported, irrespective of
which station was reached by the control panel.
Reporting to both stations with event sorting depending on what event occurred
in the system, for example, information on alarms to Station 1, and information on
troubles to Station 2 (this mode is useful where the station serves many subscribers
and it is necessary that the number likely to receive most vital information be busy as
little as possible). In this mode, during control panel programming, you can determine
which information is to be sent to which station.
Reporting to both stations: Station 1 first, then Station 2. This mode is reached by
assigning the same event to both stations.
It is possible to send information on events related to zones, partitions, as well as system
events. The event codes for both stations are the same. It is possible to define how the
events are to be divide between the two stations. Information can be transmitted to the
stations in one of fifteen formats (including Contact ID).
Because of analysis of commutation signals (algorithm ToneLOGIC), the CA-6 controls the
process of establishing connection with the station, which in case of the line being frequently
busy considerably reduces the time between occurrence of the event and sending
information to the monitoring station. As dialing retries are made immediately after detecting
the busy signal, the connection is established many times faster than with the equipment
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel CA-6 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel CA-6 in the language / languages: English as an attachment in your email.

The manual is 0,56 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel CA-6

Satel CA-6 Additional guide - English - 40 pages

Satel CA-6 Quick start guide - English - 8 pages

Satel CA-6 Additional guide - German - 19 pages

Satel CA-6 User Manual - German - 19 pages

Satel CA-6 Installation Guide - German - 80 pages

Satel CA-6 User Manual - German - 18 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info