699578
9
Zoom out
Zoom in
Previous page
1/36
Next page
CA-6 SATEL 7
panel outputs, it activates the fire alarm verification function. The verification operates as
follows: the first violation cuts the fire detectors power supply off for about 15 seconds.
The power-down results in reset of the violated detectors. Then, the power supply is
restored, but the panel will not control the “24H fire” zones for ten to twenty seconds
because of the balancing of detectors. Next, the control panel enters the special mode of
fire detectors control, which lasts about 90 seconds. If a repeated detector violation occurs
during that time, a FIRE alarm will be triggered. Otherwise, the control panel will go over
to the normal control of “24H fire” zones (duration of the whole verification process is
approx. 2 min.). The output reacts to the "RESET power supply" function (user function 9).
29 power supply with RESET function the output is designated to power detectors which
require a periodical power cut-off until the state memory is cleared. The RESET function is
activated from keypad through the user function 9 (calling: [CODE][
*
][9]). The voltage is
cut off for time programmed as the output active time.
30 TIMER the output is controlled by the control panel clock; it is activated/deactivated in the
hours indicated by a corresponding TIMER (see: Functions programming TIMERS).
31 audible alarm status the output signals the audible armed mode. Operation of the output
can be limited to the selected "list of zones" or partition.
32 full arm status the output is only active when all zones/partitions assigned to it are in the
armed mode.
33 ARM/DISARM/CLEAR ALARM the output signals the particular system states with,
respectively, one, two, or four pulses 0.16 s each.
34 alarm in keypad silent alarm signaling in the partition keypad.
35 power supply on armed mode it functions similarly to the ARM STATUS output, but it is
activated right after "exit delay" starts, not after changeover from the exit delay to the
armed mode (it can be used, for example, as indicator or power supply output for
microwave detectors in spaces where people stay).
36 signalling: LED – the output can control a LED to indicate the following statuses:
- off – control panel disarmed
- steady light – control panel armed
- blinking light – the control panel armed, there was alarm or trouble
Note: If in the armed mode any zones are violated in the system, the LED will be
blinking and will only change to steady light after the violation ends.
37 signalling: relay the output can control a relay. The output becomes active after arming,
and inactive after an alarm is triggered, a trouble occurs, or the system is disarmed.
Note: If in the armed mode any zones are violated in the system, the output will
become active after the violation ends.
38 not used (do not program).
39 no guard code the output is activated by a timer programmed as the partition control
TIMER, unless a guard code is entered within the timer specified time.
40 service mode status the output is activated if the control panel service mode has been
called from any keypad.
41 battery low status – the output, which state is updated after each battery voltage test.
Partitions
A new partition is created when at least one zone is assigned to it. The CA-6 permits creating
of two partitions to which any outputs, telephone numbers and pager messages can be
assigned, and thus enables two alarm systems to be built on the basis of one CA-6 control
panel. The partitions can be controlled from a keypad (access codes assigned to the
partitions) as well as by means of control zones. Both partitions can be controlled at the
same time.
Because the sirens connected to the outputs can be activated by selected zones, the
assignment of zones to partitions will define which codes can clear alarm on particular sirens.
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel CA-6 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel CA-6 in the language / languages: English as an attachment in your email.

The manual is 0,56 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel CA-6

Satel CA-6 Additional guide - English - 40 pages

Satel CA-6 Quick start guide - English - 8 pages

Satel CA-6 Additional guide - German - 19 pages

Satel CA-6 User Manual - German - 19 pages

Satel CA-6 Installation Guide - German - 80 pages

Satel CA-6 User Manual - German - 18 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info